Optical Instruments
Filter
Showing 391–420 of 1896 results
| Brand | Apure |
|---|---|
| Origin | Shanghai, China |
| Manufacturer Type | Manufacturer |
| Origin Category | Domestic (China) |
| Model | TS-620 |
| Price | USD 685 (FOB Shanghai) |
| Product Type | Online |
| Measurement Range | Low-Turbidity Mode (0–0.5 NTU & 5–400 NTU) |
| Resolution | 0.01 NTU (low-turbidity), 0.1 NTU (high-turbidity) |
| Operating Temperature (Transmitter) | –20 to +55 °C |
| Accuracy | ±5% FS |
| Enclosure Rating | Transmitter IP65 |
| Process Pressure (Submersible) | ≤0.3 MPa |
| Output | 4–20 mA (4-wire, max. load 750 Ω) |
| Relay Outputs | 2 programmable SPDT relays (AC230 V, 2 A) |
| Digital Interface | RS485 with Modbus RTU protocol |
| Humidity | ≤85% RH (non-condensing) |
| Brand | AQUALABO |
|---|---|
| Origin | France |
| Model | NTU |
| Type | Online Turbidity Sensor |
| Measurement Range | 0–4000 NTU |
| Resolution | 0.01 NTU |
| Accuracy | ±5% of reading |
| Operating Temperature | 0–50 °C |
| Output Protocols | Modbus RTU over RS-485 (standard), SDI-12 (optional) |
| Enclosure Rating | IP68 |
| Power Supply | 5–12 V DC |
| Typical Current Consumption | 820 µA (RS-485, 1 Hz), 4.2 mA (SDI-12, 1 Hz) |
| Dimensions | Ø27 mm × 170 mm (sensor + 3 m cable) |
| Weight | 300 g |
| Pressure Rating | 5 bar |
| Optical Principle | 90° infrared scattered light nephelometry at 850 nm |
| Calibration Standard | Formalin-based turbidity standards per NF EN 872 (0–500 mg/L) and NF T 90-105-2 (>500 mg/L) |
| Brand | AQUALABO |
|---|---|
| Origin | France |
| Model | NTU |
| Measurement Principle | 90° Infrared Light Scattering at 880 nm |
| Turbidity Range | 0–4000 NTU (5 selectable sub-ranges) |
| TSS Range | 0–4500 mg/L |
| Resolution | 0.01–1 NTU / mg/L |
| Accuracy | < ±5% of reading |
| Temperature Compensation | Integrated CTN sensor (±0.5 °C) |
| Output | Modbus RTU over RS-485 (standard), SDI-12 (optional) |
| Power Supply | 5–12 VDC |
| Typical Current Draw | 820 µA (RS-485, 1 Hz) |
| Peak Pulse | 500 mA |
| Enclosure Material | PVC, Delrin®, Quartz, PMMA, Polyamide |
| Dimensions | Ø27 mm × 170 mm |
| Weight | 300 g (sensor + 3 m cable) |
| Pressure Rating | 5 bar |
| IP Rating | IP68 |
| Operating Temperature | 0–50 °C |
| Storage Temperature | −10 to +60 °C |
| Calibration Standards | NF EN 872 (0–500 mg/L), NFT 90 105-2 (>500 mg/L) |
| Max Refresh Rate | < 1 s |
| Brand | Arcoptix |
|---|---|
| Origin | Switzerland |
| Model | ARCLIGHT-NIR, ARCLIGHT-MIR |
| Light Source Type | Tungsten-Halogen (QTH) / Silicon Carbide (SiC) Globar |
| Spectral Range | 0.4–4 µm (NIR), 1–25 µm (MIR) |
| Spectral Coverage (cm⁻¹) | 25,000–2,500 cm⁻¹ (NIR), 10,000–400 cm⁻¹ (MIR) |
| Color Temperature | ~2850 K (NIR), ~1550 K (MIR) |
| Rated Lifetime | 4,000 h (NIR), 10,000 h (MIR) |
| Power Input | 12 V DC (with integrated 100–240 V AC to 12 V DC converter) |
| Output Diameter | 12.7 mm |
| Fiber Coupling | Removable |
| Attenuation | Manual variable iris |
| Operating Temperature | 5–40 °C |
| Dimensions (L×W×H) | 92 × 92 × 43 mm (body only) |
| Weight | 390 g |
| Brand | Arcoptix |
|---|---|
| Origin | Switzerland |
| Model | ARClight NIR, ARClight IR |
| Spectral Range (NIR) | 400–4,000 nm |
| Spectral Range (IR) | 1–25 µm |
| Wavenumber Range (NIR) | 25,000–2,500 cm⁻¹ |
| Wavenumber Range (IR) | 10,000–400 cm⁻¹ |
| Filament Temperature (NIR) | ~2,850 K |
| Filament Temperature (IR) | ~1,400 K |
| Rated Lifetime (NIR) | 4,000 h |
| Rated Lifetime (IR) | 10,000 h |
| Lamp Power Options (NIR) | 5 W or 20 W |
| Lamp Power (IR) | 20 W |
| Lamp Type (NIR) | Quartz Tungsten Halogen (QTH) |
| Lamp Type (IR) | Silicon Carbide (SiC) Globar |
| Fiber Coupling Options | SMA-905 (NA = 0.25, BK7 lens) / SMA-905 (NA = 0.3, Off-axis parabolic mirror) |
| Collimated Beam Diameter | 12.7 mm |
| Operating Temperature | 5–40 °C |
| Attenuation | Manual iris diaphragm |
| Cooling | Integrated air fan |
| Input Power | 100–240 V AC to 12 V DC (included converter) |
| Dimensions (NIR, w/o coupler) | 92 × 92 × 43 mm |
| Dimensions (IR, w/ coupler) | 140 × 92 × 43 mm |
| Weight | 390 g |
| Brand | ARCoptix |
|---|---|
| Model | maestro |
| Origin | USA |
| Resolution | 4 cm⁻¹ (standard), down to 0.5 cm⁻¹ (optional) |
| Spectral Range | Configurable up to 5000–830 cm⁻¹ (2–12 µm) |
| Detector | TE-cooled MCT, Peltier-stabilized |
| Interferometer Type | Alignment-Insensitive Dual Retroreflector Design |
| Wavenumber Reproducibility | <10 ppm |
| Scan Rate | 1 spectrum/sec (continuous mode) |
| ADC | 24-bit |
| Interface | USB 2.0 |
| Power | 12 V / 8 W (interferometer only) |
| Operating Temperature | 10–40 °C |
| Dimensions | 180 × 160 × 80 mm |
| Weight | 1.8 kg |
| Software SDK | C, C#, LabVIEW, MATLAB APIs included |
| Compliance | Designed for integration into GLP/GMP- and ISO/IEC 17025-aligned systems |
| Fiber Compatibility | SMA-905, supports CIR (1–6 µm), PIR (4–18 µm), CaF₂/BK7 coupling optics |
| Brand | Arete Associates |
|---|---|
| Origin | USA |
| Manufacturer Type | Authorized Distributor |
| Import Status | Imported |
| Model | NewOpto |
| Core Technology | Diode-Pumped Solid-State (DPSS) Q-Switched Laser |
| Wavelength Options | 1064 nm, 532 nm, 355 nm, 266 nm, 1572 nm |
| Pulse Energy Range | 10–200 mJ |
| Average Power | 1–6 W |
| Pulse Width | ~3 ns (FWHM) |
| Repetition Rate | 30–100 Hz |
| Beam Quality (M²) | <5 to <10 |
| Dimensions | 185×185×102 mm³ or 259×185×120 mm³ |
| Brand | Argolight |
|---|---|
| Origin | France |
| Substrate | Fused Silica with Embedded 3D Fluorescent Patterns |
| Dimensions (ArGo-PowerLM V2) | 75 × 25 × 6 mm |
| Excitation Range | 250–650 nm |
| Immersion Compatibility | Dry, Oil (unlimited) |
| Damage Threshold | 50 GW·cm⁻² (peak or average irradiance) |
| Power Range | 10 µW to 100 mW |
| Fluorescent Pattern Count | 5 (LM/HM/SIM variants: 5/16/27) |
| Software | Daybook v3.2 (Analysis & Data Manager modules) |
| Compliance | ISO 17025 traceable calibration protocols, compatible with GLP/GMP documentation workflows |
| Brand | Armadillo SIA |
|---|---|
| Type | UV-Transmitting Silica Fiber |
| Wavelength Range | 190–1200 nm |
| Numerical Aperture (NA) | 0.22 ± 0.02 (standard), 0.26/0.28 ± 0.02 (UV-NSS) |
| Core Diameter | 300 µm |
| Cladding Diameter | 330 µm |
| Core/Cladding Material | Synthetic Fused Silica (UV-grade) |
| Buffer Type | Hard Polymer (H) or Nylon Jacket (N) |
| Jacket Color | Black (B) |
| Solarization Resistance | Enhanced (UV-NSS variant) |
| Compliance | ISO 10110-3, IEC 60793-2-40, ASTM F2754 (UV transmission stability) |
| Brand | Armadillo SIA |
|---|---|
| Type | High Numerical Aperture (NA) Multimode Fiber |
| Core Diameter | 25–3000 µm (configurable) |
| NA Range | 0.22 ± 0.02 to 0.87 ± 0.02 |
| Wavelength Range | 350–2400 nm (material-dependent) |
| Cladding Materials | Hard Polymer (HC), Silicone (UV), Germanium-doped Silica, Borosilicate Glass |
| Jacket Options | Black hard polymer buffer (H), Nylon overjacket (N) |
| Compliance | ISO 10993-5 biocompatibility tested |
| Customization | Available for core/clad geometry, length, termination, and connectorization |
| Brand | Armadillo SIA |
|---|---|
| Type | Silver Halide (AgCl/AgBr) Polycrystalline Fiber |
| Wavelength Range | 3–17 µm |
| Numerical Aperture | 0.13 ± 0.02 (MIR3), 0.25 ± 0.02 (MIR300/330), 0.35 ± 0.02 (custom variants) |
| Core Diameter | 20–3000 µm |
| Cladding Material | Polymeric (Hard Polymer Buffer for MIR300/330-H |
| Core/Cladding Ratio | Standardized per model (e.g., 300/330 µm) |
| Operating Temperature | Up to 80 °C (continuous), short-term up to 120 °C |
| Bend Radius | ≥15× outer diameter (static), ≥30× (dynamic) |
| Attenuation | <0.2 dB/m @ 10.6 µm (typ.), <0.5 dB/m across 4–12 µm band |
| Brand | Armadillo SIA |
|---|---|
| Core Configuration | Customizable Multicore |
| Wavelength Range | UV190–1200 nm (UV grade) / NIR700–2400 nm (broadband) |
| Numerical Aperture (NA) | 0.1–0.28 ±0.02 |
| Cladding Diameter | 100–2100 µm |
| Compliance | ISO 10110-3, IEC 60793-2-10, Telcordia GR-20-CORE |
| Customization | Core count, pitch, geometry, coating, termination, and connectorization available |
| Brand | Arroyo Instruments |
|---|---|
| Origin | USA |
| Model | 262 Series |
| Mounting Compatibility | TO-Can, Butterfly, C-Mount, and Custom Packages |
| Thermal Control | Integrated Peltier-based Temperature Controller (±0.1 °C Stability) |
| Electrical Interface | DB-15 / DB-9 / 9W4 Connector |
| Cooling | Forced-air with High-Conductivity Heat Sink |
| Compliance | RoHS-compliant, CE-marked, Designed for GLP-Compatible Lab Environments |
| Software Integration | Compatible with Arroyo’s TECSource™ Control Suite (USB/RS-232) |
| Brand | Arroyo Instruments |
|---|---|
| Origin | USA |
| Model | 4201 |
| Current Range | 100 mA to 20 A (dual-range configuration) |
| Output Voltage | Up to 10 V |
| Accuracy | 0.025% + 0.03 mA |
| Current Noise | < 1 µA RMS |
| Small-Signal Bandwidth | 325 kHz |
| Interface | USB & RS-232 |
| Isolation | Fully galvanically isolated I/O (input/output, photodiode input, laser output) |
| Modulation | Analog voltage input (0–5 V or ±5 V), hardware-protected |
| QCW Option | Not available on 4201 (standard CW only) |
| Compliance | CE, RoHS, FCC Class B |
| Software Compatibility | SCPI-compliant command set, backward-compatible with industry-standard laser controller protocols |
| Brand | Arroyo Instruments |
|---|---|
| Origin | USA |
| Model | 485 Series |
| Output Current Range | up to 10 A |
| Output Voltage Range | up to 15 V |
| Current Accuracy | 0.05% + offset (e.g., 0.4–1.6 mA) |
| Current Noise | < 60 µA RMS |
| Bandwidth | 45–65 kHz |
| Temperature Stability | ±0.004°C |
| Compatible Sensors | Thermistor, RTD |
| Control Interfaces | USB, RS-232, Analog (0–5 V or 0–10 V) |
| Power Output (TECPak) | 32 W / 55 W |
| Form Factor | Compact OEM module (≈1/3 volume of benchtop equivalents) |
| Brand | Arroyo Instruments |
|---|---|
| Origin | USA |
| Model | 6301 |
| Laser Current Range | 100 mA to 4 A (selectable per variant) |
| Output Voltage | Up to 10 V |
| Current Accuracy | 0.025% + 0.03 mA |
| Current Noise | < 1 µA RMS |
| Control Bandwidth | 325 kHz |
| TEC Power | 60 W |
| Temperature Sensor Support | Thermistor, RTD, LM335, AD590 |
| Interfaces | USB, RS-232 |
| Isolation | Optically and electrically isolated I/O |
| Compliance | CE, RoHS, FCC Class A |
| Software Compatibility | LabVIEW, Python, MATLAB via ASCII command protocol |
| Brand | Arroyo Instruments |
|---|---|
| Origin | USA |
| Model | 7000 Series |
| Form Factor | 1U or 2U Rack-Mountable / Benchtop |
| Laser Driver Channels | Up to 4 per unit |
| Max Laser Current | 4 A |
| Max Laser Voltage | 8 V |
| TEC Driver Channels | Up to 4 per unit |
| Max TEC Current | 18 A |
| Max TEC Voltage | 28 V |
| Max TEC Power | 420 W |
| Temperature Stability (24 h) | ±0.1 °C |
| Short-Term Stability (1 h) | <0.004 °C |
| Control Interface | Ethernet, USB |
| PID Auto-Tuning | Yes |
| Compatibility | ILX Lightwave & Newport TEC/LD command set |
| Input Power | Universal AC (90–264 VAC, 47–63 Hz) |
| Brand | Arroyo Instruments |
|---|---|
| Origin | USA |
| Model | 5240 |
| Temperature Stability | ±0.004 °C |
| Control Power Range | 28 W |
| Max Current | 4 A |
| Max Voltage | 7 V |
| Supported Sensors | Thermistor |
| Interface | USB, RS-232 |
| AutoTune PID Function | Yes |
| Display | High-contrast VFD |
| Brand | ART Photonics |
|---|---|
| Origin | Germany |
| Manufacturer Type | Authorized Distributor |
| Product Category | Imported Optical Component |
| Model | ART Fiber Series |
| Component Type | Optical Fiber Assembly |
| Core Shape | Round (custom shapes available) |
| Core Diameters | 100 µm, 200 µm, 300 µm, 400 µm, 600 µm, 800 µm |
| Core Material Options | High-OH Silica (0.18–1.2 µm), Low-OH Silica (0.35–2.5 µm) |
| Cladding | Fluorine-Doped Fused Silica |
| Numerical Aperture (Standard) | 0.22 ± 0.02 (Full Acceptance Angle: 25°) |
| Optional NA | 0.12 ± 0.02 (14°), 0.26 ± 0.02 (30°) |
| Protective Jacket Materials | Nylon, Tefzel®, Acrylate, Polyimide, Metal |
| Cable Tube | Polymer-Coated Stainless Steel |
| Length Range | 5 cm to 50 m |
| Connector Types | HP-SMA, D80 |
| Power Handling (HP-SMA) | 100 W (100 µm), 200 W (200 µm), 300 W (400 µm), 400 W (600 µm) |
| Power Handling (D80) | 150 W (100 µm), 400 W (200 µm), 600 W (400 µm), 800 W (600 µm) |
| Brand | ART Photonics |
|---|---|
| Origin | Germany |
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model Series | CIR-8, CIR-250, CIR-340, CIR-500 |
| Component Category | Optical Element |
| Core Material | As₂S₃ |
| Cladding Material | As–S |
| Wavelength Range | 1.5–6 µm |
| Core Diameter | 8–500 µm |
| Cladding Diameter | 200–550 µm |
| Coating Diameter | 300–700 µm |
| Primary Coating | PTFE |
| Secondary Coating | PVC |
| Core Refractive Index | 2.4 |
| Numerical Aperture | 0.25–0.28 |
| Max CW Power Handling | 1 W |
| Fiber Structure | Step-Index, Dual-Layer Polymer-Coated |
| Termination | SMA Connector |
| Jacket | PEEK Polymer Sheath |
| Brand | art photonics |
|---|---|
| Origin | Germany |
| Fiber Type | Step-Index Multimode Chalcogenide (CIR) |
| Wavelength Range | 1.1–6.5 µm |
| Core Diameter | 500 ± 10 µm |
| Cladding Diameter | 550 ± 15 µm |
| Numerical Aperture (NA) | 0.30 ± 0.03 |
| Coating OD | 700 ± 30 µm |
| Jacket | Dual-Polymer (PVC outer), Metal Armor Sleeve (OD 3.7 mm) |
| Length | 1.00 ± 0.05 m |
| Minimum Bend Radius | 100 mm |
| Operating Temperature | –50 °C to +90 °C |
| Connector | FC/APC (input), FC/APC (output), MP37 metal housing |
| Brand | art photonics |
|---|---|
| Origin | Germany |
| Fiber Type | Step-index multimode chalcogenide (CIR) glass |
| Wavelength Range | 1.1–6.5 µm |
| Core Diameter | 500 ± 10 µm |
| Cladding Diameter | 550 ± 15 µm |
| Numerical Aperture (NA) | 0.30 ± 0.03 |
| Coating Diameter (dual-polymer) | 700 ± 30 µm |
| Connector Type | FC/PC to FC/PC |
| Protective Jacket | Metal sheath, OD 3.7 mm |
| Length | 1.00 ± 0.05 m |
| Minimum Bend Radius | 100 mm |
| Operating Temperature | –50 °C to +90 °C |
| Attenuation | 0.2–0.3 dB/m (at 2.5–4 µm and 4.5–5 µm) |
| Brand | art photonics |
|---|---|
| Origin | Germany |
| Model | FBC-CO/CO2-10-SMA 905 |
| Connector Type | SMA 905 |
| Wavelength Range | 5–6 µm (CO) & 9–11 µm (CO₂) |
| Component Category | Optical Coupling Element |
| Compliance | CE-marked, RoHS-compliant |
| Mounting Interface | Standard optical breadboard-compatible flange |
| Brand | art photonics |
|---|---|
| Origin | Germany |
| Model | FlexiRay® CIR-Series |
| Wavelength Range | 1.1–6.5 µm |
| Core Diameter Options | 8–340 µm |
| Attenuation | 0.2–0.3 dB/m (at 2.5–4 µm and 4.5–5 µm) |
| Operating Temperature | −50 °C to +90 °C |
| Jacket Materials | PEEK, Metal-PVC, Stainless Steel, Stainless Steel with Silicone Coating |
| Connector Types | SMA-905, FC/PC, FC/APC |
| Compliance | ISO 9001-certified manufacturing |
| QC Protocol | 100% end-face inspection, interferometric surface quality verification, spectral transmission validation |
| Brand | ART Photonics |
|---|---|
| Origin | Germany |
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | FlexiRay® High-Power Laser Delivery Fiber |
| Component Category | Optical Component |
| Core Diameter Options | 100 / 200 / 300 / 400 / 600 / 800 µm |
| Core Material | Synthetic Fused Silica (High-OH for UV–VIS |
| Cladding Material | Fluorine-Doped Fused Silica |
| Jacket Materials | Nylon, Ethylene Copolymer, Acrylate, Polyimide, or Metal |
| Numerical Aperture (Standard) | 0.22 ± 0.02 (Full Acceptance Angle: 25°) |
| Optional NA | 0.12 ± 0.02 (14°) or 0.26 ± 0.02 (30°) |
| Connector Types | HP-SMA, D80 |
| Max Power Handling (Typical, CW, with Optimal Coupling) | 100–800 W depending on core size and connector |
| Cable Length Range | 5 cm to 50 m |
| Customization | Available for core geometry, NA, jacketing, and connector integration |
| Brand | ART Photonics |
|---|---|
| Origin | Germany |
| Model | PIR240/300 |
| Wavelength Range | 3–17 µm |
| Core Diameter | 240 µm |
| Cladding Diameter | 300 µm |
| Fiber Type | Polycrystalline Silver Halide (AgClBr) |
| Numerical Aperture | ~0.22 |
| Bend Radius (Min) | ≥50 mm |
| Operating Temperature | –40 °C to +80 °C |
| Connector Interface | SMA-905 (standard), optional FC/PC or custom |
| Compliance | RoHS, CE, ISO 9001-manufactured |
| Brand | ART Photonics |
|---|---|
| Origin | Germany |
| Component Type | Fiber Collimator |
| Model | FOCO-L-3/5-F20 |
| Wavelength Range | 3–5 µm |
| Lens Material | Zinc Selenide (ZnSe) |
| Focal Length | 20 mm |
| Application Domain | Mid-IR Beam Conditioning for Spectroscopy, Gas Sensing & Laser Delivery Systems |
| Brand | ART Photonics |
|---|---|
| Origin | Germany |
| Product Type | Fiber Collimator |
| Spectral Range | 8–12 µm |
| Lens Material | Zinc Selenide (ZnSe) |
| Focal Length | 20 mm |
| Model | FOCO-L-8/12-F20 |
| Component Category | Optical Instrument Component |
| Import Status | Imported |
| Brand | art photonics |
|---|---|
| Origin | Germany |
| Model | FOCO-S-3/5-F5 |
| Lens Material | Zinc Selenide (ZnSe) |
| Wavelength Range | 3–5 µm |
| Focal Length | 5 mm |
| Component Type | Optical Element |
| Compliance | ISO 10110 optical surface specifications, RoHS-compliant packaging |
| Brand | art photonics |
|---|---|
| Origin | Germany |
| Model | FOCO-S-8/12-F5 |
| Spectral Range | 8–12 µm |
| Focal Length | 5 mm |
| Lens Material | Zinc Selenide (ZnSe) |
| Component Type | Optical Collimating Assembly |
| Compliance | RoHS-compliant, CE-marked for optical instrumentation |