- All
- Favorite
- Popular
- Most rated
| Brand | A&D |
|---|---|
| Origin | Japan |
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | HU2-2S-10012-A2 |
| Price | USD 7,950 (FOB Yokohama) |
| Brand | A&D |
|---|---|
| Model | AD-8127 |
| Printing Method | Impact Dot-Matrix |
| Character Format | 7×9 dots |
| Character Size | 1.6 mm (W) × 3.2 mm (H) |
| Print Speed | ~1.6 lines/sec |
| Paper Feed Speed | ~4 lines/sec |
| Characters per Line | 24 |
| Operating Temp. | 0–40 °C, 35–85% RH (non-condensing) |
| Storage Temp. | −20–60 °C, 10–90% RH (non-condensing) |
| Interface | RS-232C / Current Loop |
| Power Supply | AC Adapter AX-TB135 or AX-TB285 (Input: AC 100 V ±10% / −15%, 50/60 Hz) |
| Power Consumption | ~36 VA (incl. adapter) |
| Dimensions (W×D×H) | 174 × 141 × 87 mm |
| Weight | ~500 g |
| Standard Accessories | Ribbon cartridge, plain paper roll, AC adapter, identification label, user manual, RS-232C cable (D-Sub9P/D-Sub25P configurable) |
| Brand | Aitesen |
|---|---|
| Origin | Japan |
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | EUV250WH-1 |
| Price | USD 3,500 (FOB Japan) |
| Brand | Asahi Sokki |
|---|---|
| Origin | Japan |
| Model | MCA-1500E |
| Heating Capacity | 1.5 kW |
| Operating Voltage | Single-phase 200 V AC |
| Temperature Range | 80–500 °C |
| Air Flow Rate | 20–200 Nℓ/min |
| Maximum Operating Pressure | 0.3 MPa |
| Sheath Material | SUS (AISI 304 or equivalent) |
| Insulation Resistance | ≥5 MΩ @ 500 V DC |
| Dielectric Strength | 400 V AC, 1 min, leakage current ≤10 mA |
| Surface Temperature | Reduced via optimized thermal design |
| Energy Efficiency | ~15% lower power consumption vs. conventional air heaters |
| Brand | ASAHI Precision (A&D) |
|---|---|
| Origin | Japan |
| Model | 735BB1 |
| Pressure Range | 0–0.3 MPa |
| Input Signal | 0–5 V DC (configurable to 0–10 V or 4–20 mA) |
| Supply | External pilot pressure required, no internal air supply |
| Power | 24 V DC |
| Port Size | 3/8″ NPT |
| Valve Body Material | ADC12 aluminum alloy |
| Diaphragm & Seal Material | NBR standard (Viton, Teflon, polyurethane optional) |
| Orifice Diameter | 11 mm |
| Response Time | <0.05 s (no-load) |
| Hysteresis | ≤ ±0.05% FS |
| Linearity | ≤ ±0.3% FS (sensor-dependent) |
| Consumption | ≤1.5 L/min (standard), up to 5 L/min (high-speed variant) |
| Weight | 1.8 kg |
| Insulation Resistance | >1 MΩ |
| Mounting Orientation | Omnidirectional (no orientation-induced drift) |
| Sensor Compatibility | External analog sensors — pressure (voltage/current), flow, position (0–10 V or 4–20 mA) |
| Control Principle | Force-balance + digital PID algorithm |
| Operating Fluid | Compressed air only (external pilot-controlled relief mode) |
| Brand | ASAHI Precision |
|---|---|
| Origin | Japan |
| Model | 601D-D05 |
| Measuring Principle | Differential Pressure (ΔP) Based Volumetric Flow Calculation |
| Wetted Materials | SUS316L |
| Operating Pressure Range | 100–300 kPa |
| Flow Range | 5–100 CCPM (mL/min) |
| Output Signal | 0–5 V DC |
| Supply Voltage | 24 V DC |
| Response Time | <1 ms |
| Ambient Temperature Range | 0–40 °C |
| Connection Port | G¼ (BSPP) |
| Weight | 700 g |
| Compliance | Designed for clean fluid applications including purified water systems |
| Sample Compatibility | Liquids compatible with SUS316L |
| Enclosure Rating | IP65 (typical for industrial transmitter housing) |
| Brand | ASAHI (A&D) |
|---|---|
| Origin | Japan |
| Model | 942BA1 / 943BA1 / 944BA1 |
| Operating Pressure Range | Up to 1.0 MPa |
| Max. Fluid Temperature | ≤150 °C |
| Wetted Materials | SUS316 Body, PTFE Diaphragm, Viton Seals |
| Control Principle | Force-Balance + PI Feedback Control |
| Input Signal Options | 0–10 V DC, 4–20 mA, or 10 V DC (configurable) |
| Supply Pressure Requirement | ≤⅔ of max. operating pressure + α (model-dependent) |
| Power Supply | 24 V DC |
| Flow Consumption | ≤1.5 L/min (standard), ≤5 L/min (high-speed variant) |
| Response Time (no-load) | <0.5 s |
| Linearity | ±1% FS |
| Hysteresis | ≤±0.2% FS |
| Resolution | ≤1/2000 of full scale |
| Electrical Isolation | >1 MΩ |
| Input Impedance | ≥1 kΩ (voltage), ≤300 Ω (current) |
| Connection Ports | 1/4″, 3/8″, 1/2″ NPT/Female |
| Orifice Diameter | 4 mm / 8 mm / 16 mm |
| Weight | 0.8 kg / 2.1 kg / 2.3 kg |
| Mounting Orientation | Omnidirectional (zero-point drift ≤±1% depending on orientation) |
| Brand | ASAHI |
|---|---|
| Origin | Japan |
| Model | S670S0.3 / S670S1 |
| Input Voltage | DC 24 V |
| Supply Pressure Range (Primary) | 60–150 kPa (S670S0.3) / 140–200 kPa (S670S1) |
| Output Pressure Range (Secondary, Adjustable) | 0.15–30.00 kPa (S670S0.3) / 0.5–100.00 kPa (S670S1) |
| Max. Supply Pressure | 150 kPa / 200 kPa |
| Pressure Sensor Type | Piezoresistive Silicon |
| Display | 4-digit LED (character height 10 mm) |
| Accuracy | ±1% FS |
| Response Time | ≤5 s |
| Operating Temperature | 0–40 °C |
| Interface | Φ6 push-to-connect fittings |
| Remote Analog Input Options | 0–5 V, 0–10 V, or 4–20 mA (model-suffix coded) |
| Output Flow Rate | 0–50 nL/min |
| Dimensions (W×H×D) | 96×96×138.5 mm |
| Weight | ~1.2 kg |
| Fluid Compatibility | Dry air only |
| Compliance | CE-marked for industrial use (IEC 61000-6-2/6-4), RoHS compliant |
| Key | Brand: ASAHI Precision |
|---|---|
| Origin | Japan |
| Model | 635BA1 |
| Supply Pressure | Not required |
| Input Signal | 0–5 V DC (configurable to 0–10 V / 4–20 mA) |
| Output Pressure Range | 0–0.8 MPa |
| Power Supply | 24 V DC |
| Port Size | 1/8″ NPT (1/4″ available via model variant) |
| Operating Fluid | Compressed air only |
| Control Principle | Force-balance + digital PID |
| Response Time | < 0.05 s (no-load) |
| Hysteresis | ≤ ±0.05% FS |
| Linearity | ≤ ±0.3% FS (sensor-dependent) |
| Flow Consumption | ≤ 1.5 L/min (standard) |
| Weight | 0.8 kg |
| Insulation Resistance | ≥ 1 MΩ |
| Diaphragm Material | NBR |
| Body Material | ADC12 aluminum alloy |
| Seal Material | NBR |
| Sensor Interface | Analog voltage (≥10 kΩ input impedance) or current (≤300 Ω input impedance) |
| Mounting Orientation | Omnidirectional (no orientation-induced drift) |
| Orifice Diameter | 4 mm |
| Compliance | CE-marked |
| Brand | ASAHI Precision (A&D) |
|---|---|
| Origin | Japan |
| Model | 944BA1 |
| Operating Pressure Range | Up to 1.0 MPa |
| Input Signal Options | 0–5 V, 0–10 V, or 4–20 mA (configurable via model suffix) |
| Pilot Pressure Requirement | ≤ 2/3 × max. operating pressure + α |
| Power Supply | 24 VDC |
| Port Size | 1/2″ |
| Fluid Compatibility | Liquids and gases non-corrosive to PTFE, Viton®, and brass |
| Diaphragm Material | PTFE |
| Seal Material | Viton® |
| Valve Body Material | Brass |
| Full-Scale Orifice Diameter | Φ16 mm |
| Zero Drift | ±1% FS (orientation-dependent) |
| Control Principle | Force-balance + PI feedback control |
| Hysteresis | ≤ ±0.2% FS |
| Linearity | ≤ ±1% FS |
| Response Time (no-load) | < 0.5 s |
| Air Consumption | ≤ 5 L/min (high-speed variant) |
| Weight | 2.3 kg |
| Insulation Resistance | > 1 MΩ |
| Input Impedance | ≥ 1 kΩ (voltage), ≤ 300 Ω (current) |
| Brand | ASAHI Precision |
|---|---|
| Origin | Japan |
| Model | S650SML / S650SMH |
| Pressure Range (S650SML) | 3.5–700 kPa |
| Pressure Range (S650SMH) | 12.5–2500 kPa |
| Set Resolution | 0.01 kPa (S650SML), 0.1 kPa (S650SMH) |
| Input Signal | 0–10 V DC |
| Supply Pressure | 800 ± 20 kPa (S650SML), 3000 ± 200 kPa (S650SMH) |
| Accuracy | ±0.14% FS |
| Zero & Span Temp. Coefficient | ±0.018% FS/°C |
| Display | 5-digit LED (kPa) |
| Control Principle | Force-Balanced Electrostatic Capacitance Sensing with PI Feedback |
| Supply Voltage | 24 V DC |
| Power Input | 100 V AC |
| Warm-up Time | ≤30 min |
| Operating Temperature | 5–40 °C |
| Dimensions (W×D×H) | 280 × 210 × 133 mm |
| Weight | ~3 kg |
| Inlet/Outlet Port | Rc 1/4 (S650SML), Rc 3/8 (S650SMH) |
| Orifice Diameter | Φ4 mm (S650SML), Φ11 mm (S650SMH) |
| Max. Consumption Flow | ≤1.5 L/min |
| Insulation Resistance | ≥1 MΩ |
| Brand | ASAHI Precision |
|---|---|
| Origin | Japan |
| Model | 6640AA1 |
| Supply Pressure Range | Up to 0.85 MPa (max input = set range + 0.05 MPa) |
| Output Pressure Range (Selectable) | 0–0.8 MPa (AA1), 0–0.3 MPa (AB1), 0–0.1 MPa (AD1), 0–1.0 MPa (AH1) |
| Input Signal | 0–5 V DC (optional: 0–10 V DC or 4–20 mA, specify at order) |
| Power Supply | 24 V DC ±10% |
| Sensor Type | Built-in pressure sensor (A-series) or external analog sensor interface (B-series, supports pressure/flow/position sensors) |
| Input Impedance | ≥10 kΩ (voltage), ≤300 Ω (current) |
| Hysteresis | ≤±0.05% FS |
| Linearity | ≤±0.3% FS (sensor-dependent) |
| Response Time (no-load) | <0.05 s |
| Flow Consumption | ≤1.5 L/min (standard), ≤5 L/min (high-speed variant) |
| Orifice Diameter | 4 mm |
| Weight | 0.8 kg |
| Housing Material | ADC12 aluminum die-cast |
| Internal Components | A2017 aluminum alloy, SUS304 stainless steel |
| Diaphragm | NBR or Viton® |
| Seals | Viton® |
| Insulation Resistance | >1 MΩ |
| Mounting Orientation | Omnidirectional (no orientation-induced drift) |
| Fluid Compatibility | Compressed air (non-air media require externally piloted configuration) |
| Brand | AND/A&D |
|---|---|
| Origin | Japan |
| Model | BM-5 |
| Maximum Capacity | 5.2 g |
| Minimum Readability | 1 µg (0.001 mg) |
| Repeatability | ±0.0012 mg (at 1 g load) |
| Linearity | ±0.010 mg |
| Stabilization Time (FAST mode) | ~10 s |
| Dimensions (W×D×H) | 259 × 466 × 326 mm |
| Net Weight | ~10 kg |
| Power Supply | AC 100 V (±10%, −15%), 50/60 Hz, ~30 VA |
| Interfaces | USB (Quick USB, Windows 10 compatible), RS-232C (D-Sub 9-pin male) |
| Brand | AND/A&D |
|---|---|
| Origin | Japan |
| Model | SV-10 |
| Viscosity Range | 0.3–10,000 mPa·s |
| Repeatability | ±1% (std. dev.) |
| Accuracy | ±3% (1–1,000 mPa·s) |
| Operating Temp. Range | 0–160 °C (0.1 °C resolution) |
| Excitation Frequency | Fixed at 30 Hz |
| Sensor Material | Gold-plated SUS304 stainless steel |
| Power Supply | AC adapter (100 V AC) |
| Interface | RS-232C |
| Software Included | WinCT-Viscosity (Windows) |
| Brand | AND/A&D |
|---|---|
| Origin | Japan |
| Model | MS-50 |
| Capacity | 50 g |
| Readability | 50 mg |
| Net Weight | 295 g |
| Dimensions (W×D×H) | 195 × 80 × 135 mm |
| Housing Material | Impact-Resistant Engineering Resin |
| Packaging Dimensions | 400 × 300 × 270 mm |
| Certification | JIS Class III Compliant (Certified by Japanese National Metrology Institute, stamped official certificate provided) |
| Brand | AND/A&D |
|---|---|
| Origin | Japan |
| Model | 752AC1 / 752BC1 |
| Set Pressure Range | –0.06 to 0.3 MPa |
| Input Signal | 0–10 V / 4–20 mA (standard 10–5 V configurable) |
| Supply Pressure | Max. Output Range + 0.1 MPa |
| Power Supply | 24 VDC |
| Connection Port | 3/8″ |
| Compatible Fluid | Compressed Air (non-air media require external pilot type) |
| Sensor Type | Internal piezoresistive pressure sensor (752AC1) / External sensor interface (752BC1) |
| Input Impedance | ≥10 kΩ (voltage) / ≤300 Ω (current) |
| Mounting Orientation | Omnidirectional (no orientation-induced drift) |
| Control Algorithm | Force-Balance + Adaptive PID |
| Air Consumption | ≤1.5 L/min (low-flow variant) to ≤5 L/min (standard) |
| Weight | 1.8 kg |
| Insulation Resistance | ≥1 MΩ |
| Hysteresis | ≤±0.1% FS |
| Linearity | ≤±0.5% FS (sensor-dependent) |
| Response Time | <0.05 s (no-load) |
| Orifice Diameter | 11 mm |
| Body Material | ADC12 aluminum alloy (A2017 equivalent) |
| Diaphragm & Seal Material | NBR |
| Brand | APEL |
|---|---|
| Origin | Japan |
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | M2HA-350X |
| Pricing | Upon Request |
| Rated Voltage/Current | AC125V/1–50 mA, AC250V/1–50 mA, DC5V/1–50 mA, DC48V/1–50 mA |
| Electrical Life | ≥3,000 cycles (at rated load) |
| Trip Temperature | OFF at ≥350°C (±5°C), ON at ≤325°C (±5°C) |
| Differential | 25 K |
| Dimensions | 56 × 17 × 9 mm |
| Housing Material | Alumina (Al₂O₃) ceramic |
| Max. Ambient Operating Temperature | 400°C |
| Application | Overheat protection for heating elements and electronic control units |
| Brand | AND/A&D |
|---|---|
| Origin | Japan |
| Model | BM-252 |
| Capacity | 250 g |
| Readability | 0.01 mg |
| Repeatability (Std Dev) | 0.03 mg |
| Linearity | ±0.10 mg |
| Weighing Chamber Diameter | Φ90 mm |
| Stabilization Time | ~8 s (FAST mode) |
| Dimensions (W×D×H) | 259 × 466 × 326 mm |
| Net Weight | ~10 kg |
| Interfaces | USB (high-speed), RS-232C (9-pin D-Sub) |
| Electrostatic Control | Patented DC Ion Generator with Conductive Glass Draft Shield |
| Brand | AND |
|---|---|
| Origin | Japan |
| Model | AD4212A-100 |
| Capacity | 110 g |
| Readability | 0.1 mg |
| Stabilization Time (FAST mode) | ≤1.1 s (0–30 g), ≤1.3 s (30–110 g) |
| Pan Size | 50 × 50 mm |
| Pan Material | SUS316 |
| Interface | RS-232C (bidirectional, 600–19200 bps) |
| Comparator Outputs | 3-level relay contacts with buzzer |
| Input Signals | Tare, Print |
| IP Rating | IP54 |
| Dimensions (W×D×H) | 80 × 250 × 320 mm (measuring unit only) |
| Accessories | Calibration weight, AC adapter, draft shield, instruction manual |
| Brand | AND |
|---|---|
| Model | FX-200i |
| Capacity | 220 g |
| Minimum Readability | 0.001 g |
| Pan Diameter | φ130 mm |
| Repeatability (SD) | ±0.001 g |
| Display Update Rate | 5 / 10 / 20 Hz selectable |
| Power Supply | AC adapter (100 V ±10–15%, 50/60 Hz) |
| Power Consumption | ~11 VA |
| Dimensions (W×D×H) | 193 × 262.5 × 84.5 mm |
| Net Weight | ~2.5 kg |
| Pan Material | SUS304 stainless steel |
| Interface | RS-232C (D-sub 9-pin male) |
| Units | g, %, carat, monme |
| Included Accessories | Draft shield, protective cover, AC adapter |
| Brand | ACE GIKEN |
|---|---|
| Origin | Japan |
| Material | SUS314 stainless steel |
| Sterilization Method | Vacuum-compatible |
| Maximum Working Pressure | 0.5 MPa |
| Volume Capacity | 1.8 L |
| Mounting Type | Top-discharge (BU series) |
| Compliance | Designed for pharmaceutical and biotech cleanroom environments |
| Customization Options | Level sensors, residual volume detection, agitators (25 W / 40 W), sight glasses, LCD indicators |
| Brand | ACE GIKEN |
|---|---|
| Origin | Japan |
| Model | AT-F1000 / AT-F4000 |
| Capacity Range | 10–80 L (working volume) |
| Construction Material | SUS314 stainless steel |
| Sterilization Method | Vacuum-assisted thermal sterilization |
| Pressure Rating | Up to 0.34 MPa (AT-F1000/2000), 0.18 MPa (AT-F4000/6000/8000) |
| Agitation Options | Static (no agitation) or Air-driven agitation (AM series) |
| Inner Vessel Available | Yes, model-specific SUS314 inner containers |
| Compliance | Designed for GLP-compliant bioprocess development and pilot-scale cell culture applications |
| Brand | ACE GIKEN |
|---|---|
| Origin | Japan |
| Manufacturer Type | Authorized Distributor |
| Product Category | Imported Instrument |
| Model | TC-100 / TC-250 / TC-150C |
| Material | SUS314 Stainless Steel |
| Sterilization Method | Vacuum Sterilization |
| Cartridge Capacity | 100 g, 150 g, 250 g |
| Brand | ACE GIKEN |
|---|---|
| Origin | Japan |
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | DPS-800SPⅡ |
| Housing Material | SUS314 Stainless Steel |
| Sterilization Method | Vacuum Sterilization |
| Control Architecture | Microprocessor-Based Dual-Parameter Independent Adjustment (Liquid Pressure, Atomizing Air Pressure, Dispense Duration) |
| Valve Core Technology | Balpet® Precision Metering Valve Platform |
| Integration Interface | TTL/24 VDC I/O Terminals |
| Hose Compatibility | PU Tubing (φ4×φ2.5 mm, φ6×φ4 mm), Nylon Tubing (φ8×φ6 mm) |
| Nozzle Options | Interchangeable Internal/External Atomization Nozzles (Custom Sizing Available) |
| Regulatory Compliance | Designed for ISO 13485-aligned bioprocess environments |
| Sterility Assurance | Compatible with vacuum-based depyrogenation and terminal sterilization protocols |
Show next