- All
- Favorite
- Popular
- Most rated
| Brand | A&D |
|---|---|
| Origin | Japan |
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | HU2-2S-10012-A2 |
| Price | USD 7,950 (FOB Yokohama) |
| Brand | Aitesen |
|---|---|
| Origin | Japan |
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | EUV250WH-1 |
| Price | USD 3,500 (FOB Japan) |
| Brand | Asahi Sokki |
|---|---|
| Origin | Japan |
| Model | MCA-1500E |
| Heating Capacity | 1.5 kW |
| Operating Voltage | Single-phase 200 V AC |
| Temperature Range | 80–500 °C |
| Air Flow Rate | 20–200 Nℓ/min |
| Maximum Operating Pressure | 0.3 MPa |
| Sheath Material | SUS (AISI 304 or equivalent) |
| Insulation Resistance | ≥5 MΩ @ 500 V DC |
| Dielectric Strength | 400 V AC, 1 min, leakage current ≤10 mA |
| Surface Temperature | Reduced via optimized thermal design |
| Energy Efficiency | ~15% lower power consumption vs. conventional air heaters |
| Brand | ASAHI Precision (A&D) |
|---|---|
| Origin | Japan |
| Model | 735BB1 |
| Pressure Range | 0–0.3 MPa |
| Input Signal | 0–5 V DC (configurable to 0–10 V or 4–20 mA) |
| Supply | External pilot pressure required, no internal air supply |
| Power | 24 V DC |
| Port Size | 3/8″ NPT |
| Valve Body Material | ADC12 aluminum alloy |
| Diaphragm & Seal Material | NBR standard (Viton, Teflon, polyurethane optional) |
| Orifice Diameter | 11 mm |
| Response Time | <0.05 s (no-load) |
| Hysteresis | ≤ ±0.05% FS |
| Linearity | ≤ ±0.3% FS (sensor-dependent) |
| Consumption | ≤1.5 L/min (standard), up to 5 L/min (high-speed variant) |
| Weight | 1.8 kg |
| Insulation Resistance | >1 MΩ |
| Mounting Orientation | Omnidirectional (no orientation-induced drift) |
| Sensor Compatibility | External analog sensors — pressure (voltage/current), flow, position (0–10 V or 4–20 mA) |
| Control Principle | Force-balance + digital PID algorithm |
| Operating Fluid | Compressed air only (external pilot-controlled relief mode) |
| Brand | ASAHI Precision |
|---|---|
| Origin | Japan |
| Model | 601D-D05 |
| Measuring Principle | Differential Pressure (ΔP) Based Volumetric Flow Calculation |
| Wetted Materials | SUS316L |
| Operating Pressure Range | 100–300 kPa |
| Flow Range | 5–100 CCPM (mL/min) |
| Output Signal | 0–5 V DC |
| Supply Voltage | 24 V DC |
| Response Time | <1 ms |
| Ambient Temperature Range | 0–40 °C |
| Connection Port | G¼ (BSPP) |
| Weight | 700 g |
| Compliance | Designed for clean fluid applications including purified water systems |
| Sample Compatibility | Liquids compatible with SUS316L |
| Enclosure Rating | IP65 (typical for industrial transmitter housing) |
| Brand | ASAHI (A&D) |
|---|---|
| Origin | Japan |
| Model | 942BA1 / 943BA1 / 944BA1 |
| Operating Pressure Range | Up to 1.0 MPa |
| Max. Fluid Temperature | ≤150 °C |
| Wetted Materials | SUS316 Body, PTFE Diaphragm, Viton Seals |
| Control Principle | Force-Balance + PI Feedback Control |
| Input Signal Options | 0–10 V DC, 4–20 mA, or 10 V DC (configurable) |
| Supply Pressure Requirement | ≤⅔ of max. operating pressure + α (model-dependent) |
| Power Supply | 24 V DC |
| Flow Consumption | ≤1.5 L/min (standard), ≤5 L/min (high-speed variant) |
| Response Time (no-load) | <0.5 s |
| Linearity | ±1% FS |
| Hysteresis | ≤±0.2% FS |
| Resolution | ≤1/2000 of full scale |
| Electrical Isolation | >1 MΩ |
| Input Impedance | ≥1 kΩ (voltage), ≤300 Ω (current) |
| Connection Ports | 1/4″, 3/8″, 1/2″ NPT/Female |
| Orifice Diameter | 4 mm / 8 mm / 16 mm |
| Weight | 0.8 kg / 2.1 kg / 2.3 kg |
| Mounting Orientation | Omnidirectional (zero-point drift ≤±1% depending on orientation) |
| Brand | ASAHI |
|---|---|
| Origin | Japan |
| Model | S670S0.3 / S670S1 |
| Input Voltage | DC 24 V |
| Supply Pressure Range (Primary) | 60–150 kPa (S670S0.3) / 140–200 kPa (S670S1) |
| Output Pressure Range (Secondary, Adjustable) | 0.15–30.00 kPa (S670S0.3) / 0.5–100.00 kPa (S670S1) |
| Max. Supply Pressure | 150 kPa / 200 kPa |
| Pressure Sensor Type | Piezoresistive Silicon |
| Display | 4-digit LED (character height 10 mm) |
| Accuracy | ±1% FS |
| Response Time | ≤5 s |
| Operating Temperature | 0–40 °C |
| Interface | Φ6 push-to-connect fittings |
| Remote Analog Input Options | 0–5 V, 0–10 V, or 4–20 mA (model-suffix coded) |
| Output Flow Rate | 0–50 nL/min |
| Dimensions (W×H×D) | 96×96×138.5 mm |
| Weight | ~1.2 kg |
| Fluid Compatibility | Dry air only |
| Compliance | CE-marked for industrial use (IEC 61000-6-2/6-4), RoHS compliant |
| Key | Brand: ASAHI Precision |
|---|---|
| Origin | Japan |
| Model | 635BA1 |
| Supply Pressure | Not required |
| Input Signal | 0–5 V DC (configurable to 0–10 V / 4–20 mA) |
| Output Pressure Range | 0–0.8 MPa |
| Power Supply | 24 V DC |
| Port Size | 1/8″ NPT (1/4″ available via model variant) |
| Operating Fluid | Compressed air only |
| Control Principle | Force-balance + digital PID |
| Response Time | < 0.05 s (no-load) |
| Hysteresis | ≤ ±0.05% FS |
| Linearity | ≤ ±0.3% FS (sensor-dependent) |
| Flow Consumption | ≤ 1.5 L/min (standard) |
| Weight | 0.8 kg |
| Insulation Resistance | ≥ 1 MΩ |
| Diaphragm Material | NBR |
| Body Material | ADC12 aluminum alloy |
| Seal Material | NBR |
| Sensor Interface | Analog voltage (≥10 kΩ input impedance) or current (≤300 Ω input impedance) |
| Mounting Orientation | Omnidirectional (no orientation-induced drift) |
| Orifice Diameter | 4 mm |
| Compliance | CE-marked |
| Brand | ASAHI Precision (A&D) |
|---|---|
| Origin | Japan |
| Model | 944BA1 |
| Operating Pressure Range | Up to 1.0 MPa |
| Input Signal Options | 0–5 V, 0–10 V, or 4–20 mA (configurable via model suffix) |
| Pilot Pressure Requirement | ≤ 2/3 × max. operating pressure + α |
| Power Supply | 24 VDC |
| Port Size | 1/2″ |
| Fluid Compatibility | Liquids and gases non-corrosive to PTFE, Viton®, and brass |
| Diaphragm Material | PTFE |
| Seal Material | Viton® |
| Valve Body Material | Brass |
| Full-Scale Orifice Diameter | Φ16 mm |
| Zero Drift | ±1% FS (orientation-dependent) |
| Control Principle | Force-balance + PI feedback control |
| Hysteresis | ≤ ±0.2% FS |
| Linearity | ≤ ±1% FS |
| Response Time (no-load) | < 0.5 s |
| Air Consumption | ≤ 5 L/min (high-speed variant) |
| Weight | 2.3 kg |
| Insulation Resistance | > 1 MΩ |
| Input Impedance | ≥ 1 kΩ (voltage), ≤ 300 Ω (current) |
| Brand | ASAHI Precision |
|---|---|
| Origin | Japan |
| Model | S650SML / S650SMH |
| Pressure Range (S650SML) | 3.5–700 kPa |
| Pressure Range (S650SMH) | 12.5–2500 kPa |
| Set Resolution | 0.01 kPa (S650SML), 0.1 kPa (S650SMH) |
| Input Signal | 0–10 V DC |
| Supply Pressure | 800 ± 20 kPa (S650SML), 3000 ± 200 kPa (S650SMH) |
| Accuracy | ±0.14% FS |
| Zero & Span Temp. Coefficient | ±0.018% FS/°C |
| Display | 5-digit LED (kPa) |
| Control Principle | Force-Balanced Electrostatic Capacitance Sensing with PI Feedback |
| Supply Voltage | 24 V DC |
| Power Input | 100 V AC |
| Warm-up Time | ≤30 min |
| Operating Temperature | 5–40 °C |
| Dimensions (W×D×H) | 280 × 210 × 133 mm |
| Weight | ~3 kg |
| Inlet/Outlet Port | Rc 1/4 (S650SML), Rc 3/8 (S650SMH) |
| Orifice Diameter | Φ4 mm (S650SML), Φ11 mm (S650SMH) |
| Max. Consumption Flow | ≤1.5 L/min |
| Insulation Resistance | ≥1 MΩ |
| Brand | ASAHI Precision |
|---|---|
| Origin | Japan |
| Model | 6640AA1 |
| Supply Pressure Range | Up to 0.85 MPa (max input = set range + 0.05 MPa) |
| Output Pressure Range (Selectable) | 0–0.8 MPa (AA1), 0–0.3 MPa (AB1), 0–0.1 MPa (AD1), 0–1.0 MPa (AH1) |
| Input Signal | 0–5 V DC (optional: 0–10 V DC or 4–20 mA, specify at order) |
| Power Supply | 24 V DC ±10% |
| Sensor Type | Built-in pressure sensor (A-series) or external analog sensor interface (B-series, supports pressure/flow/position sensors) |
| Input Impedance | ≥10 kΩ (voltage), ≤300 Ω (current) |
| Hysteresis | ≤±0.05% FS |
| Linearity | ≤±0.3% FS (sensor-dependent) |
| Response Time (no-load) | <0.05 s |
| Flow Consumption | ≤1.5 L/min (standard), ≤5 L/min (high-speed variant) |
| Orifice Diameter | 4 mm |
| Weight | 0.8 kg |
| Housing Material | ADC12 aluminum die-cast |
| Internal Components | A2017 aluminum alloy, SUS304 stainless steel |
| Diaphragm | NBR or Viton® |
| Seals | Viton® |
| Insulation Resistance | >1 MΩ |
| Mounting Orientation | Omnidirectional (no orientation-induced drift) |
| Fluid Compatibility | Compressed air (non-air media require externally piloted configuration) |
| Brand | AND/A&D |
|---|---|
| Origin | Japan |
| Model | BM-5 |
| Maximum Capacity | 5.2 g |
| Minimum Readability | 1 µg (0.001 mg) |
| Repeatability | ±0.0012 mg (at 1 g load) |
| Linearity | ±0.010 mg |
| Stabilization Time (FAST mode) | ~10 s |
| Dimensions (W×D×H) | 259 × 466 × 326 mm |
| Net Weight | ~10 kg |
| Power Supply | AC 100 V (±10%, −15%), 50/60 Hz, ~30 VA |
| Interfaces | USB (Quick USB, Windows 10 compatible), RS-232C (D-Sub 9-pin male) |
| Brand | AND/A&D |
|---|---|
| Origin | Japan |
| Model | MS-50 |
| Capacity | 50 g |
| Readability | 50 mg |
| Net Weight | 295 g |
| Dimensions (W×D×H) | 195 × 80 × 135 mm |
| Housing Material | Impact-Resistant Engineering Resin |
| Packaging Dimensions | 400 × 300 × 270 mm |
| Certification | JIS Class III Compliant (Certified by Japanese National Metrology Institute, stamped official certificate provided) |
| Brand | AND/A&D |
|---|---|
| Origin | Japan |
| Model | 752AC1 / 752BC1 |
| Set Pressure Range | –0.06 to 0.3 MPa |
| Input Signal | 0–10 V / 4–20 mA (standard 10–5 V configurable) |
| Supply Pressure | Max. Output Range + 0.1 MPa |
| Power Supply | 24 VDC |
| Connection Port | 3/8″ |
| Compatible Fluid | Compressed Air (non-air media require external pilot type) |
| Sensor Type | Internal piezoresistive pressure sensor (752AC1) / External sensor interface (752BC1) |
| Input Impedance | ≥10 kΩ (voltage) / ≤300 Ω (current) |
| Mounting Orientation | Omnidirectional (no orientation-induced drift) |
| Control Algorithm | Force-Balance + Adaptive PID |
| Air Consumption | ≤1.5 L/min (low-flow variant) to ≤5 L/min (standard) |
| Weight | 1.8 kg |
| Insulation Resistance | ≥1 MΩ |
| Hysteresis | ≤±0.1% FS |
| Linearity | ≤±0.5% FS (sensor-dependent) |
| Response Time | <0.05 s (no-load) |
| Orifice Diameter | 11 mm |
| Body Material | ADC12 aluminum alloy (A2017 equivalent) |
| Diaphragm & Seal Material | NBR |
| Brand | AND/A&D |
|---|---|
| Origin | Japan |
| Model | BM-252 |
| Capacity | 250 g |
| Readability | 0.01 mg |
| Repeatability (Std Dev) | 0.03 mg |
| Linearity | ±0.10 mg |
| Weighing Chamber Diameter | Φ90 mm |
| Stabilization Time | ~8 s (FAST mode) |
| Dimensions (W×D×H) | 259 × 466 × 326 mm |
| Net Weight | ~10 kg |
| Interfaces | USB (high-speed), RS-232C (9-pin D-Sub) |
| Electrostatic Control | Patented DC Ion Generator with Conductive Glass Draft Shield |
| Brand | ADVANTEC (Yan Hua Dong Yang) |
|---|---|
| Origin | Japan |
| Model | 10-905 |
| Type | Manual Date/Number Embossing Punch |
| Max. Sheet Capacity | 10 sheets (64 g/m² paper, 8-digit imprint) |
| Cycle Time | 1.5 s/cycle (50 Hz) / 1.2 s/cycle (60 Hz) |
| Dimensions | 214 × 295 × 485 mm |
| Weight | 12.7 kg |
| Die Block Compatibility | MOLE 905-208 |
| Power Supply | None (Manual Operation) |
| Brand | ADVANTEC (Toyo) |
|---|---|
| Origin | Japan |
| Model | DRH653WB |
| Heating Method | Forced-air convection (right-side horizontal airflow) |
| Temperature Range | Ambient + 50 °C to 500 °C |
| Temperature Control Accuracy | ±0.5 °C at 500 °C |
| Temperature Uniformity | ±6 °C at 500 °C |
| Ramp Time | Approx. 90 min (from ambient to 500 °C) |
| Chamber Dimensions (W×D×H, mm) | 600 × 600 × 600 (effective height 540 mm) |
| External Dimensions (W×D×H, mm) | 1240 × 1040 × 1800 |
| Chamber Volume | ~216 L |
| Shelf Capacity | 4 fixed-position shelves (140 mm pitch) |
| Exhaust Port | Φ50 mm |
| Measurement Port | Rc1/4 |
| Power Supply | AC 200 V, 3-phase, 27.5 A (50/60 Hz) |
| Net Weight | ~420 kg |
| Standard Accessories | 2 shelf plates |
| Brand | ADVANTEC (Toyo Roshi Kaisha, Ltd.) |
|---|---|
| Origin | Japan |
| Model | UHP-90K |
| Filter Diameter | 90 mm |
| Chamber Capacity | 600 mL |
| Minimum Concentration Volume | 15 mL |
| Residual Liquid Volume | 0.6 mL |
| Effective Filtration Area | 50.7 cm² |
| Operating Speed Range | 0–100 rpm |
| Max Working Pressure | 0.49 MPa |
| Safety Valve Set Pressure | 0.39 ± 0.09 MPa |
| Materials | Body/Acrylic, Top & Bottom Plates/Polysulfone, O-rings/Silicone, Structural Components/SUS304, Polyacetal, FPM |
| Outlet Tubing Adapter ID | 3 mm |
| Dimensions (H × W) | 222 × 144 mm |
| Weight | 1.8 kg |
| Packaging | 160 × 260 × 160 mm, 2.0 kg |
| Brand | Advantec (Distributor) |
|---|---|
| Origin | Japan |
| Model | PAN160-7A |
| Output | 0–160 V / 0–7 A |
| Max. Power | 1120 W |
| Line Regulation (CV) | ≤0.01% + 2 mV |
| Load Regulation (CV) | ≤0.02% + 5 mV |
| Ripple & Noise (rms) | <1 mV |
| Temperature Coefficient (CV) | 100 ppm/°C |
| Transient Response Time (20% load step) | ≤50 µs |
| OVP, OTP, Foldback Current Limiting, Front Terminal Cover, Isolation Voltage | ±500 Vdc to chassis |
| Compliance | IEC 61010-1, EN 61326-1 (EMC), UL/cUL 61010-1 |
| Brand | Advantec |
|---|---|
| Origin | Japan |
| Manufacturer Type | Authorized Distributor |
| Country of Origin | Imported |
| Model | KDC2-D01 |
| Power Supply | Single-phase AC 100 V, 50/60 Hz |
| Dimensions (W×D×H) | 250 × 280 × 260 mm |
| Weight | 9 kg |
| Airflow Capacity | 1.3 m³/min |
| Maximum Static Pressure | 9.0 kPa |
| Hose Diameter | Φ50 mm (Φ38 mm optional) |
| Packaging Dimensions | 400 × 390 × 310 mm |
| Gross Weight | 10 kg |
| Brand | A&D (AND) |
|---|---|
| Origin | Japan |
| Model | 913BA1 / 914BA1 / 916BA1 |
| Operating Pressure Range | Up to 1.5 MPa |
| Input Signal | 0–10 V DC, 4–20 mA (configurable) |
| Pilot Pressure | 0.3 MPa |
| Supply Voltage | 24 V DC |
| Port Size | 1/4", 3/8", 1/2" |
| Fluid Compatibility | Liquids and gases non-corrosive to PTFE, Viton®, and brass |
| Input Impedance | ≥1 kΩ (voltage), ≤300 Ω (current) |
| Control Principle | Force-Balance + PI Algorithm |
| Hysteresis | ≤±0.2% FS |
| Linearity | ≤±1% FS |
| Response Time | <0.5 s (no-load) |
| Flow Consumption | ≤1.5 L/min (standard), ≤5 L/min (high-speed) |
| Weight | 2.2 kg / 3.4 kg / 6.8 kg |
| Valve Body Material | Brass |
| Diaphragm | PTFE |
| Seal Material | Viton® |
| Insulation Resistance | >1 MΩ |
| Mounting Orientation | Omnidirectional (zero-point drift ≤±1% FS dependent on orientation) |
| Orifice Diameter | 6 mm / 10 mm / 14 mm |
Show next