X-Ray Instruments
Filter
Showing 631–660 of 786 results
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Model | CrankScan |
| Power Supply | 90–260 VAC, 49–61 Hz, single-phase |
| Inrush Current | 40 A @ 115 VAC / 80 A @ 230 VAC (cold start) |
| Nominal Power Consumption | 100 VA (150 VA during battery charging) |
| Magnetization Frequency Range | 1.0–1000 Hz |
| Magnetization Voltage | 0–16 V |
| Signal Analysis Bandwidths | 10–70 kHz, 70–200 kHz, 200–450 kHz |
| Channel Configuration | Single-channel or multi-channel (configurable) |
| Probe Compatibility | Interchangeable probes for journals, fillets, flanks, shoulders, and crank webs |
| Measurement Time per Surface | 6–8 seconds |
| IP Rating | IP20 |
| Operating Temperature | 0–40 °C |
| Relative Humidity | 10–90 % RH (non-condensing) |
| Storage Humidity | 10–90 % RH (non-condensing) |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Model | CrankScan200 |
| Detection Principle | Magnetic Barkhausen Noise (MBN) |
| Measurement Type | Non-Destructive, Surface & Near-Surface Integrity Assessment |
| Channel Configuration | Single- or Multi-Channel Probe Support |
| Probe Compatibility | Curved-Surface Optimized Sensors for Journal, Fillet, Flank, and Crankweb Geometry |
| Alarm Thresholding | User-Configurable Signal Amplitude & Statistical Deviation Limits |
| Compliance Framework | Supports ISO 28671 (Non-destructive testing — Magnetic Barkhausen noise testing — General principles), ASTM E3094 (Standard Guide for MBN Testing of Ferromagnetic Materials), and GLP/GMP-aligned data traceability |
| Brand | Stresstech Oy |
|---|---|
| Country of Origin | Finland |
| Model | DR45 |
| Type | Portable X-ray Diffraction (XRD)-Based Residual Stress Analyzer |
| Measurement Principle | Sin²ψ Method with Cr-Kα Radiation |
| Detector | High-Sensitivity Si-PIN or CCD (Configurable) |
| Angular Range | 2θ = 135°–165° (Optimized for Fe, Ni, Ti, Al, and Co-based alloys) |
| Sample Positioning | Motorized XYZ Stage with Manual Fine-Adjustment |
| Data Acquisition Time | < 90 s per measurement point (typical) |
| Stress Resolution | ≤ ±10 MPa (Fe-based steels, under optimal surface condition) |
| Depth Sensitivity | Surface-to-near-surface (~1–20 µm, dependent on material and radiation) |
| Compliance | ASTM E915-22, ISO 21913:2019, EN 15305:2021 |
| Brand | Stresstech Oy |
|---|---|
| Country of Origin | Finland |
| Model | G2 |
| Portability | Field-deployable, integrated water-cooled X-ray generator |
| Safety Compliance | EN 61000-6-4, EN 61000-6-2, IEC 61000-4-3, CE-marked for industrial use |
| Detector Type | High-resolution silicon strip detector (SSD) or CCD-based imaging detector (configurable) |
| X-ray Source | Microfocus tungsten anode tube, 30–50 kV adjustable, <100 µm focal spot |
| Measurement Method | Sin²ψ technique with automated ψ-tilt stage (±45° range) |
| Data Acquisition | Real-time diffraction pattern capture, peak fitting via pseudo-Voigt deconvolution |
| Software Platform | RoboScan™ v5.x with GLP-compliant audit trail and 21 CFR Part 11-ready user access control |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Model | Gearscan |
| Measurement Principle | Barkhausen Noise Analysis (BNA) |
| Applicable Gear Types | Spur, Helical, Bevel, and Worm Gears |
| Diameter Range | 5–2000 mm |
| Module Range | 1–70 |
| Measurement Time per Tooth | 2–30 s (dependent on geometry and surface condition) |
| Motion Control | PC-controlled precision DC servo motor with linear-bearing-driven probe |
| Compliance | Designed for ISO 286-1, ASTM E1444/E1444M (magnetic particle testing reference), and compatible with GLP/GMP data integrity requirements |
| Software | GearScan™ v5.x with audit trail, measurement parameter programming, alarm threshold setting, spatial mapping of burn locations, statistical reporting, and CSV/PDF export |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Model | GearScan |
| Sensor Types | Multiple options available (surface, contour, bore, extended-reach) |
| Measurement Principle | Magnetic Barkhausen Noise (MBN) Analysis |
| Material Compatibility | Ferritic steels, iron-based alloys, nickel-based superalloys, cobalt-based alloys |
| Power Supply | Rechargeable Li-ion battery (≥20 h continuous operation) |
| Data Storage | 100+ raw waveform datasets with timestamps |
| Software | ViewScan data acquisition & analysis software (optional) |
| Compliance | Designed for ISO 13304-1, ASTM E3085, and industrial NDT QA/QC workflows |
| Enclosure | Ruggedized all-metal housing, IP54-rated |
| Interface | USB-C for PC connectivity, optional printer output |
| Alarm Function | User-definable threshold-based pass/fail indication |
| Display | Integrated high-contrast LCD with real-time voltage/current monitoring, battery status, and menu navigation |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Model | GearScan |
| Measurement Principle | Barkhausen Noise Analysis (BNA) |
| Diameter Range | 5–2000 mm |
| Module Range | 1–70 |
| Measurement Time per Tooth | 2–30 s (dependent on geometry and surface condition) |
| Motion Control | Computer-controlled precision DC servo motor with linear-bearing-driven probe |
| Compliance | Designed for ISO 13302, ASTM E2964, and EN 10327-based residual stress and grinding burn assessment workflows |
| Software | RoboScan™ PC-based acquisition and analysis suite with audit trail, user access levels, and GLP/GMP-ready reporting |
| Brand | Stresstech Oy |
|---|---|
| Country of Origin | Finland |
| Model | GearScan |
| Detection Principle | Magnetic Barkhausen Noise (MBN) |
| Channel Configuration | Single- or Multi-Channel |
| Compliance | ISO 28080, ASTM E3071, EN 10326 |
| Software Platform | EasyGear v5.x with Audit Trail & User Access Control |
| Data Output | CSV, XML, PDF Reports |
| Sensor Interface | Plug-and-Play Quick-Connect (DIN 41612) |
| Motion Control | Motorized X/Z Linear Axes + A/T Rotational Axes |
| Safety | Interlocked Sliding Door, Emergency Stop, CE/UKCA Marked Cabinet |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Model | GearScan |
| Measurement Principle | Barkhausen Noise Analysis (BNA) |
| Diameter Range | 5–2000 mm |
| Module Range | 1–70 |
| Measurement Time per Tooth | 2–30 s (dependent on gear geometry and surface condition) |
| Motion Control | PC-controlled precision DC servo motor with linear bearing–guided probe |
| Compliance | Designed for ISO 11368, ASTM E1444/E1444M, and EN 10204 Type 3.1 documentation support |
| Software | GearScan Suite v5.x with audit trail, user access levels, and FDA 21 CFR Part 11–ready configuration options |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Manufacturer Status | Authorized Distributor |
| Origin Category | Imported |
| Model | GearScan |
| Pricing | Available Upon Request |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Model | GearScan |
| Measurement Principle | Barkhausen Noise Analysis (BNA) |
| Diameter Range | 5–2000 mm |
| Module Range | 1–70 |
| Measurement Time per Tooth | 2–30 s (dependent on gear geometry and surface condition) |
| Motion Control | Computer-controlled precision DC servo motor with linear bearing–guided probe positioning |
| Compliance | ISO 286, ASTM E1447, EN 10002-1, applicable to ISO/IEC 17025 accredited labs |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Model | GearScan |
| Sensor Compatibility | Rollscan 250/300 ecosystem |
| Power | Rechargeable Li-ion battery (≥20 h continuous operation) |
| Data Storage | 100+ raw datasets with waveform |
| Software | ViewScan (optional standalone data acquisition & analysis) |
| Compliance | Designed for ASTM E3078, ISO 21906, and EN 10327-compliant magnetic Barkhausen noise (MBN) evaluation |
| Sample Geometry Support | External/inner diameters, raceways, shafts, cam lobes, landing gear components |
| Material Coverage | Ferritic steels, martensitic alloys, nickel-based superalloys, cobalt-chromium alloys |
| Measurement Principle | Non-destructive magnetic Barkhausen noise analysis (MBN) |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Model | CamScan |
| Measurement Principle | Magnetic Barkhausen Noise (MBN) Analysis |
| Application | Non-destructive grinding burn and heat treatment defect detection on ferromagnetic components |
| Compliance | Designed per ISO 20086, ASTM E3154 (guideline), and aligned with automotive OEM process validation requirements (e.g., GM W31, Ford WHT-502, VW PV 2079) |
| Channel Configuration | Single- or multi-channel operation |
| Probe Options | Surface-contact transducers for cam lobes, journals, and complex geometries |
| Data Output | Real-time MBN amplitude & frequency spectrum, RMS voltage, peak-to-peak noise, and derivative-based burn index |
| Software Interface | CamView™ v5.2 with configurable pass/fail thresholds, statistical process control (SPC) export, and audit-trail logging compliant with FDA 21 CFR Part 11 (optional configuration) |
| Key | Brand: Stresstech Oy |
|---|---|
| Origin | Finland |
| Model | Camscan |
| Power Supply | 90–260 VAC, 49–61 Hz, single-phase |
| Max Inrush Current (cold start) | 40 A @ 115 VAC / 80 A @ 230 VAC |
| Max Power Consumption (battery charging) | 150 VA |
| Typical Operating Power | 100 VA |
| Magnetization Frequency Range | 1.0–1000 Hz |
| Magnetization Voltage | 0–16 V |
| Analysis Filter Bands | 10–70 kHz, 70–200 kHz, 200–450 kHz |
| Channel Configuration | Single-channel (standard), optional multi-channel upgrade |
| Compliance | CE, RoHS, EN 61326-1 (EMC for industrial environments) |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Model | XSTRESS 3000 |
| Type | Portable X-ray Diffraction (XRD)-Based Residual Stress Analyzer |
| Measurement Geometry | Modified ψ-tilt (symmetrical side-inclination) |
| Detector | Dual 512-channel solid-state linear imaging detector |
| Standard ψ-angle range | –45° to +45° |
| Optional extended ψ-range | –45° to +60° |
| Φ-rotation | Optional |
| Motion control | Computer-driven high-precision DC servo motors |
| Cooling | Integrated closed-loop water cooling system with heat exchanger and recirculating chiller |
| Radiation safety | Fully compliant with IEC 61010-1, IEC 62471, and EN 61331-1 for industrial X-ray equipment |
| Regulatory status | CE-marked, Class 1 radiation device under EU Directive 2013/59/Euratom |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Model | XStress |
| Type | Robotic X-ray Diffraction (XRD)-Based Residual Stress Analyzer |
| Detection Principle | Sin²ψ Method with Monochromatic Cu Kα or Cr Kα Radiation |
| Detector Technology | Solid-State Linear Pixel Array Detector |
| Safety Compliance | EN 61000-6-4, EN 61000-6-2, IEC 61508 SIL2 (Embedded Interlock Architecture) |
| Software Platform | XTronic v5.2 (FDA 21 CFR Part 11 Compliant Audit Trail, GLP/GMP-Ready Reporting) |
| Robotic Integration | 6-Axis Industrial Robot with Real-Time Path Compensation and Surface Normal Tracking |
| Brand | Stresstech Oy |
|---|---|
| Origin | Netherlands |
| Manufacturer Status | Authorized Distributor |
| Origin Category | Imported |
| Model | PRISM |
| Pricing | Upon Request |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | Prism |
| Pricing | Upon Request |
| Brand | Stresstech Oy |
|---|---|
| Country of Origin | Finland |
| Model | RoboScan600 |
| Measurement Principle | Magnetic Barkhausen Noise (MBN) |
| Diameter Range | 5–2000 mm |
| Module Range | 1–70 |
| Measurement Time per Tooth | 2–30 s (dependent on gear geometry and surface condition) |
| Motion Control | Computer-controlled precision DC servo motor with linear bearing–guided probe actuation |
| Operation Modes | Manual and fully automated |
| Sample Handling Cycle Time | ≤20 s for gear loading/unloading |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Model | Rollscan 250 |
| Type | Portable Electromagnetic Non-Destructive Testing (NDT) System for Surface Integrity Assessment |
| Compliance | ISO 24681 (Barkhausen Noise Testing), ASTM E3097 (Standard Guide for Electromagnetic Acoustic Transduction and Barkhausen Noise Measurements) |
| Channel Configuration | Single- or Multi-Channel Operation |
| Probe Options | Interchangeable Sensor Heads for Shaft Neck, Flank, Fillet, and Contoured Geometries |
| Measurement Time per Point | < 5 s |
| Environmental Rating | IP54, Operational Temperature Range: −10 °C to +50 °C |
| Data Interface | USB 3.0, Ethernet |
| Software Platform | ViewScan v5.x with GLP/GMP-Aware Audit Trail and FDA 21 CFR Part 11 Optional Modules |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Model | Rollscan 250 |
| Detection Principle | Magnetic Barkhausen Noise (MBN) |
| Measurement Type | Non-destructive surface integrity assessment |
| Channel Configuration | Single- or multi-channel probe interface |
| Typical Measurement Time | < 5 seconds per location |
| Compliance | Designed for ISO 28671, ASTM E3179 (under development), and GLP-aligned data traceability |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Model | Rollscan 250 |
| Type | Non-Destructive Surface Integrity Analyzer |
| Measurement Principle | Magnetic Barkhausen Noise (MBN) Analysis |
| Compliance | ISO 28640, ASTM E3147 (under development), EN 10327 (applicable for grinding burn assessment) |
| Sensor Interface | Plug-and-play modular connector |
| Motion Control | Motorized X/Z linear axes + A/T rotational axes |
| Software Platform | EasyGear v5.x (Windows-based, FDA 21 CFR Part 11 compliant configuration available) |
| Data Output | ASCII, CSV, XML |
| Cabinet Integration | Integrated control cabinet with main isolator switch, LED status indicators, emergency stop, door interlock, and Ergotron-display mounting |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | Rollscan 250 |
| Pricing | Upon Request |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Model | Rollscan 250 |
| Application | Non-destructive grinding burn and heat treatment damage detection |
| Measurement Principle | Magnetic Barkhausen Noise (MBN) analysis |
| Compliance | ASTM E3167, ISO 20954, EN 10327 (applicable to MBN-based surface integrity assessment) |
| Sensor Interface | Plug-and-play modular connector |
| Motion Control | Motorized X/Z linear axes + A/T rotational axes |
| Software Platform | EasyGear v5.x (Windows-based, FDA 21 CFR Part 11 compliant audit trail optional) |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Model | Rollscan 250 |
| Detection Principle | Magnetic Barkhausen Noise (MBN) |
| Channel Configuration | Single- or Multi-channel Probe Support |
| Measurement Time | ~2–5 seconds per spot |
| Environmental Rating | IP54 (industrial-grade dust/moisture resistance) |
| Compliance | ASTM E3167, ISO 20981, EN 10327 (applicable to MBN-based surface integrity assessment) |
| Software Platform | ViewScan v5.x with GLP-compliant audit trail and FDA 21 CFR Part 11 optional modules |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Model | Rollscan 250 |
| Detection Principle | Magnetic Barkhausen Noise (MBN) |
| Measurement Type | Non-destructive, surface-sensitive residual stress & microstructural degradation assessment |
| Typical Cycle Time | 6–8 seconds per inspection zone |
| Channel Configuration | Single- or multi-channel probe support |
| Output | Quantitative MBN amplitude & frequency spectrum, burn severity index, pass/fail thresholding |
| Compliance | Designed for ISO 28080 (non-destructive testing — magnetic Barkhausen noise testing), compatible with GLP/GMP documentation workflows |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Model | Rollscan 250 |
| Power Supply | AC/DC compatible |
| Detection Principle | Magnetic Barkhausen Noise (MBN) |
| Application Scope | Surface grinding burn, residual stress gradient, microstructural changes in ferromagnetic materials |
| Probe Options | Flat, curved, slot, and custom geometry probes |
| Output | Real-time analog/digital signal, threshold-based visual & audible alarm |
| Compliance | Designed for ISO 28671, ASTM E3142 (under development), and GLP-aligned data logging |
| Brand | Stresstech Oy |
|---|---|
| Country of Origin | Finland |
| Model | Rollscan 250 |
| Detection Principle | Barkhausen Noise Analysis (BNA) |
| Channel Configuration | Single- or Multi-Channel |
| Software Platform | EasyGear v4.x |
| Compliance | ISO 28178, ASTM E3169, EN 10327 (applicable to surface integrity assessment), CE, RoHS |
| Operating Environment | Lab, QC Floor, and Production Line (IP54-rated portable unit) |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Model | Rollscan 250 |
| Sensor Compatibility | Interchangeable MBN probes (standardized with Rollscan 300 platform) |
| Signal Processing | Digital Signal Processor (DSP)-based real-time analysis |
| Measurement Depth Range | 10–400 µm (material- and probe-dependent) |
| Output Parameters | MBN voltage amplitude, RMS value, peak frequency, spectral centroid, full-width-at-half-maximum (FWHM), and integrated energy density |
| Compliance | Designed for ISO 26892:2022 (Non-destructive testing — Magnetic Barkhausen noise and magnetic flux leakage methods — General principles), ASTM E3072-17 (Standard Guide for Magnetic Barkhausen Noise Testing), and compatible with GLP/GMP documentation workflows via ViewScan software audit trail functionality |
| Power Supply | 100–240 V AC, 50/60 Hz |
| Operating Temperature | 10–40 °C |
| Enclosure Rating | IP20 |
| Brand | Stresstech Oy |
|---|---|
| Origin | Finland |
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | RollScan 250 |
| Quotation | Upon Request |
| Power Supply | 90–260 VAC, 49–61 Hz, Single-Phase |
| Inrush Current | 40 A @ 115 VAC / 80 A @ 230 VAC (Cold Start) |
| Power Consumption | 100 VA (Normal Operation), 150 VA (Battery Charging) |
| Magnetization Frequency Range | 1.0–1000 Hz |
| Magnetization Voltage Range | 0–16 V |