Physical Property Testing Instruments
Filter
Showing 6601–6630 of 12515 results
| Brand | Yasuda Precision Machinery |
|---|---|
| Origin | Japan |
| Model | No.184-A |
| Compliance Standards | JIS A 1454, JIS A 5705 |
| Test Load Sequence | 9 N pre-load (zeroing within 5 s), followed by 133 N main load (indentation reading after 60 s) |
| Measurement Output | Indentation depth (mm) under standardized static loading |
| Origin | Japan |
|---|---|
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | MCP-HT450 |
| Pricing | Upon Request |
| Origin | Japan |
|---|---|
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | MCP-T360 |
| Pricing | Upon Request |
| Measurement Method | Four-Point Probe (Constant Current) |
| Resistance Range | 10⁻² – 10⁶ Ω |
| Supported Test Currents | 100 mA, 10 mA, 1 mA |
| Accuracy | ±1.0% ±20 digits / ±1.0% ±5 digits / ±0.5% ±5 digits / ±0.5% ±3 digits / ±2.0% ±5 digits (range-dependent) |
| Display | LCD |
| Power Supply | DC 6.5 V, 350 mA |
| Probe Interface | Dedicated MCP Four-Point Probes (ASP, ESP, PSP, BSP, QPP, TFP) |
| Data Output | RS-232C |
| Dimensions & Weight | 100 × 230 × 45 mm, 500 g |
| Standard Probe | MCP-TP03P (4-point, integrated needle length 5 mm, tip radius 0.37 mm) |
| Optional Probes | MCP-TP08P (4 mm needle, Ø2 mm tip, 240 g/needle spring force), MCP-TP06P (1.5 mm needle, 0.26 mm tip radius, 70 g/needle), MCP-TPQPP (2.2 mm needle, 0.37 mm tip radius, 210 g/needle), MCP-TP05P (1 mm needle, 0.15 mm tip radius, 50 g/needle), MCP-TFP (1 W detector for ASP/ESP probes) |
| Origin | Japan |
|---|---|
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | MCP-T610 |
| Pricing | Upon Request |
| Measurement Method | Four-Point Probe, Constant Current Method |
| Resistance Range | 10⁻³ Ω to 10⁷ Ω |
| Supported Test Currents | 100 mA, 10 mA, 1 mA, 100 µA, 10 µA, 1 µA, 0.1 µA |
| Accuracy | ±2.0% ±20 digits (10⁻³–10⁻¹ Ω), ±1.0% ±5 digits (10⁰–10² Ω), ±1.0% ±3 digits (10³–10⁴ Ω), ±0.5% ±3 digits (10⁵ Ω), ±1.0% ±3 digits (10⁶ Ω), ±2.0% ±5 digits (10⁷ Ω) |
| Power Supply | AC 85–264 V, 47–63 Hz |
| Battery Backup | ~3 years (rechargeable lithium battery) |
| Probe Types | ASP, ESP, PSP, BSP, QPP, TFP (all four-point collinear probes) |
| Standard Probe | MCP-TP03P (4-pin, needle length 5 mm, tip radius 0.37 mm) |
| Calibration Checker | MCP-TRF1 (1 Ω standard resistor for ASP/ESP probes) |
| Optional Probes | MCP-TP08P (4 mm needle, Ø2 mm tip, 240 g/needle spring force), MCP-TP06P (1.5 mm needle, 0.26 mm tip radius, 70 g/needle), MCP-TPQPP (2.2 mm needle, 0.37 mm tip radius, 210 g/needle), MCP-TP05P (1 mm needle, 0.15 mm tip radius, 50 g/needle), MCP-TFP (dedicated thin-film probe) |
| Data Interface | RS232C |
| Dimensions & Weight | 330 × 270 × 88 mm, 3.4 kg |
| Display | 5.7-inch LCD |
| Data Storage Capacity | 1000 measurements |
| Preloaded Measurement Files | 18 user-configurable test setups |
| Origin | Jilin, China |
|---|---|
| Manufacturer Type | Authorized Distributor |
| Origin Category | Domestic (PRC) |
| Model | MD-J |
| Pricing | Available Upon Request |
| Measurement Range | 0.8–3.5 g/cm³ |
| Sample Mass | 5–12 g |
| Accuracy | ±1% |
| Scale Graduation | 0.01 (0.8–2.0), 0.02 (2.0–2.5), 0.05 (2.5–3.5) g/cm³ |
| Sample Requirements | Bubble-free, smooth-surfaced, oil- and contaminant-free specimens |
| Brand | Alphavita |
|---|---|
| Model | MDF-540DH |
| Temperature Range | –20 °C to –40 °C |
| External Dimensions (W×D×H) | 793 × 770 × 1806 mm |
| Internal Dimensions (W×D×H) | 649 × 614 × 600 mm × 2 |
| Total Net Volume | 548 L |
| Net Weight | 175 kg |
| Rated Input Power | 491 W |
| Refrigerant | Hydrocarbon (R290/R600a) |
| Control Interface | Microprocessor-based digital controller with non-volatile memory |
| Communication | Standard RS485 port, optional USB data export |
| Safety | Dual-key locking system (integrated key lock + provision for auxiliary padlock) |
| Construction | Powder-coated steel interior and exterior panels |
| Cooling System | Direct-cooling evaporator coils embedded in inner cabinet walls |
| Shelf Configuration | Adjustable-height wire shelving per compartment |
| Origin | Hunan, China |
|---|---|
| Manufacturer Type | Authorized Distributor |
| Origin Category | Domestic (China) |
| Model | MDZ-II |
| Pricing | Available Upon Request |
| Maximum Sample Volume | 40 cm³ |
| Accuracy | ±0.15% |
| Repeatability | ±0.05% |
| Density Resolution | 0.0001 g/cm³ |
| Carrier Gas | High-Purity Helium or Nitrogen |
| Operating Pressure | ~1.25 atm |
| Dimensions | 385 × 335 × 200 mm |
| Origin | USA |
|---|---|
| Supplier Type | Authorized Distributor |
| Origin Category | Imported |
| Model | ME 1300-3 |
| Pricing | Available Upon Request |
| Origin | USA |
|---|---|
| Supplier Type | Authorized Distributor |
| Import Status | Imported |
| Model | ME1200 |
| Pricing | Available Upon Request |
| Brand | Other Brands |
|---|---|
| Origin | Imported |
| Manufacturer Type | Authorized Distributor |
| Price | USD 16,800 (FOB) |
| Model | OKPZ-50 |
| Drop Height Range | 50–1000 mm (adjustable in 50 mm increments) |
| Impact Mass Options | 300 g, 500 g, 1000 g, 2000 g |
| Hammer Tip Radius | 7.9 mm (5/16″), 12.7 mm (1/2″), 6.35 mm (1/4″), 4.76 mm (3/16″), 3.18 mm (1/8″), 1.59 mm (1/16″) |
| Specimen Holder Radii | 8.1 mm (1/4″), 15 mm (approx. 9/16″) — flat and spherical configurations |
| Dimensions (L×W×H) | 580 × 450 × 1280 mm |
| Net Weight | ~60 kg |
| Waveform Generation | Half-sine, trapezoidal, and terminal-peak sawtooth shock pulses |
| Control Method | Digital height setting with optical feedback loop |
| Compliance | IEC 60068-2-27, MIL-STD-810H Method 516.8, GJB 150.18A, JIS C 0041, ASTM D3332 |
| Brand | Other Brands |
|---|---|
| Origin | Imported |
| Manufacturer Type | Authorized Distributor |
| Price | USD 14,500 (FOB) |
| Waveform Options | Half-Sine (Standard), Trapezoidal & Reverse-Peak Sawtooth (Optional) |
| Height Control | Digital Positioning with ±0.5 mm Repeatability |
| 制动 System | Hydraulic Post-Impact Arrest Mechanism |
| Damping | Multi-Stage Isolation Mounts for Structural Vibration Suppression |
| Drive Motor | DC Servo with Variable-Speed Control |
| Origin | UK |
|---|---|
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | MultiTest 2.5-xt |
| Instrument Type | Universal Testing Machine (UTM) |
| Max Load Capacity | 2500 N |
| Crosshead Travel | 590 mm |
| Load Resolution | 1:6500 |
| Load Accuracy | ±0.1% of full scale |
| Speed Range | 1–1000 mm/min (≤2 kN), 1–750 mm/min (>2 kN) |
| Sensor Range Options | 2 N to 2500 N |
| Weight | 27 kg |
| Standalone Operation | Yes |
| Touchscreen Interface | Integrated 7" color LCD |
| Password Protection | Enabled |
| Sensor Auto-Recognition | Supported |
| Software Upgrade Path | Emperor™ v6.x compatible |
| Brand | Mecmesin |
|---|---|
| Origin | United Kingdom |
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model Series | OmniTest |
| Instrument Type | Electromechanical Universal Testing Machine |
| Load Capacity Options | 0.5 kN, 1 kN, 2.5 kN (Single-Column) |
| Control Interface | PC-based VectorPro™ Software or Optional Touchscreen Console |
| Footprint | Minimal benchtop space |
| Compliance | Designed to support ASTM E4, ISO 7500-1, ISO 527, ISO 6892-1, and USP <1041> mechanical testing requirements |
| Brand | Mecwins |
|---|---|
| Origin | Spain |
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported Instrument |
| Model | SCALA |
| Pricing | Available Upon Request |
| Brand | OK Instruments |
|---|---|
| Model Series | OK-TH-80 to OK-TH-1000 |
| Internal Dimensions (W×H×D, cm) | 40×50×40 to 100×100×100 |
| External Dimensions (W×H×D, cm) | 100×165×100 to 180×200×180 |
| Temperature Range Options | 0–150°C / −20–150°C / −40–150°C / −70–150°C |
| Humidity Range | 20–98% RH (optional: 5–98% RH or 10–98% RH) |
| Temperature Uniformity | ±0.5°C |
| Humidity Uniformity | ±2.5% RH |
| Temperature Stability | ±2°C |
| Humidity Stability | +2–3% RH |
| Resolution | 0.1°C / 0.1% RH |
| Heating Rate | ~4.0°C/min |
| Cooling Rate | ~1.0°C/min |
| Refrigeration System | Hermetically sealed, low-noise, dual-stage compressor with eco-friendly refrigerants R404A/R23 |
| Control Interface | LCD touch screen controller with bilingual (English/Chinese) display |
| Construction Material | SUS#304 stainless steel interior and exterior |
| Standard Accessories | One Φ50 mm cable port |
| Power Supply | AC 380 V ±5%, 50 Hz ±0.5 Hz, 3-phase 5-wire, 2.5 m cable |
| Compliance Standards | MIL-STD-810G (Method 501.6, 502.6), IEC 60068-2-1 (Cold), IEC 60068-2-2 (Dry Heat), IEC 60068-2-78 (Steady-State Damp Heat), IEC 60068-2-30 (Cyclic Damp Heat), GB/T 2423.1–2001, GB/T 2423.2–2001, GB/T 2423.4–1993, GJB 150.3–1986, GJB 150.4–1986 |
| Brand | MEI / Marlin Engineering |
|---|---|
| Origin | USA |
| Manufacturer Type | Authorized Distributor |
| Product Origin | Imported |
| Model | ME1500-3 + ME1900-5 |
| Pricing | Available Upon Request |
| Brand | MEI / Marlin Engineering |
|---|---|
| Origin | USA |
| Supplier Type | Authorized Distributor |
| Product Origin | Imported |
| Model | ME 1500-3 + ME 2000-1 |
| Pricing | Available Upon Request |
| Brand | MEI / Marlin Engineering |
|---|---|
| Origin | USA |
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | ME1500-3 + ME2100-1 |
| Pricing | Upon Request |
| Brand | MEI / Marlin Engineering |
|---|---|
| Origin | USA |
| Model | ME1200-1 |
| Compliance | FAR 25 Appendix F Part IV, Airbus AITM 2.0006, Boeing BSS 7322 |
| Radiant Flux | 35 kW/m² |
| Heating Source | Four glow bars |
| Temperature Control | Dual independent PID controllers |
| Sample Introduction | Pneumatic actuated pusher with shielded access door |
| Burner Configuration | Fixed upper burner + movable lower burner |
| Calibration System | Movable T-type calibration burner with mass flow controller |
| Heat Flux Measurement | Water-cooled thermopile with active cooling circuit |
| Airflow Control | Regulated isothermal and isovolumetric supply via orifice flow meter |
| Data Acquisition | Integrated DAQ system with ASTM/ISO-compliant heat release rate test software |
| Brand | MEI/Marlin Engineering |
|---|---|
| Origin | USA |
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | ME1500-3 + ME1700-3 |
| Pricing | Available Upon Request |
| Brand | MEMMERT |
|---|---|
| Origin | Germany |
| Manufacturer Type | Direct Manufacturer |
| Origin Category | Imported |
| Model | BIO-FITOCLIMA 12000PH |
| Internal Dimensions (D×W×H) | 436 × 222.5 × 261 cm |
| Temperature Range | +5°C to +45°C (with light ON), 0°C to +45°C (with light OFF) |
| Humidity Range | 40–80% rH (light ON), 40–90% rH (light OFF) |
| Volume Options | 5,000–25,000 L (customizable) |
| Brand | MEMMERT |
|---|---|
| Origin | Germany |
| Manufacturer Type | Direct Manufacturer |
| Origin Category | Imported |
| Model | BIO-FITOCLIMA 20000PH |
| Internal Dimensions (D×W×H) | 596 × 222.5 × 261 cm |
| Temperature Range | +5°C to +45°C (with light ON), 0°C to +45°C (with light OFF) |
| Humidity Range | 40–80% rH (light ON), 40–90% rH (light OFF) |
| Chamber Volume | ~25,000 L (standard configuration) |
| Control Interface | ClimaPlus® color touchscreen |
| Shelving | Adjustable stainless steel racks with anti-slip, corrosion-resistant surface |
| Alarm System | Configurable high/low temperature & humidity alarms with remote notification capability |
| Brand | MEMMERT |
|---|---|
| Origin | Germany |
| Manufacturer Type | Original Equipment Manufacturer (OEM) |
| Country of Origin | Germany |
| Model | BIO-FITOCLIMA 25000PH |
| Internal Dimensions (D×W×H) | 436 × 422.5 × 261 cm |
| Temperature Range | +5 °C to +45 °C (with light on), 0 °C to +45 °C (light off) |
| Humidity Range | 40–80 % rH (light on), 40–90 % rH (light off) |
| Volume | 25,000 L |
| Control Interface | ClimaPlus® color touchscreen |
| Shelving | Adjustable stainless steel, corrosion-resistant, non-slip, cleanable |
| Alarm System | Configurable high/low temperature & humidity alarms with remote notification capability |
| Compliance | Designed for GLP-compliant environments |
| Brand | MEMMERT |
|---|---|
| Origin | Germany |
| Model | CTC / TTC |
| Chamber Interior | Stainless Steel 1.4301 (ASTM 304) |
| Insulation | Triple-layer aerospace-grade thermal insulation |
| Refrigeration System | Dual parallel compressors with electronically controlled refrigerant injection |
| Defrosting | Automatic cyclic defrost |
| Evaporator | Stainless steel |
| Temperature Range | –40 °C to +180 °C |
| Ramp Rate | Cooling: 80 min (180 °C → –40 °C) |
| Heating | 20 min (–40 °C → 180 °C) |
| Humidity Control | Available in TTC variant (optional integrated steam humidifier) |
| Noise Level | Low-noise operation (<62 dB(A)) |
| Interface | USB, printer port, optional Ethernet |
| Construction | Embossed stainless steel exterior, galvanized steel rear panel, double-glazed insulated door with stainless steel frame |
| Standard Accessories | 1 stainless steel grid shelf |
| Mobility | Lockable casters |
| Brand | MEMMERT |
|---|---|
| Origin | Germany |
| Model | CTC256 |
| Instrument Type | Upright Chamber |
| Temperature Range (with humidity control) | +10 °C to +95 °C |
| Temperature Range (dry operation) | −42 °C to +190 °C |
| Humidity Range | 10–98 %RH |
| Temperature Uniformity | ±0.5 K to ±2 K |
| Temperature Stability | ±0.5 °C |
| Internal Volume | 256 L |
| Internal Dimensions (W×H×D) | 640 × 670 × 597 mm |
| External Dimensions (W×H×D) | 898 × 1730 × 1100 mm |
| Power Supply | 400 V, 3-phase, 50 Hz |
| Rated Power | ~7,000 W |
| Net Weight | ~362 kg |
| Compliance Certificates | Factory Calibration at −20 °C to +160 °C |
| Brand | MEMMERT |
|---|---|
| Origin | Germany |
| Manufacturer | MEMMERT GmbH + Co. KG |
| Chamber Type | Upright Vertical |
| Models | HCP50 / HCP105 / HCP150 / HCP240 |
| Temperature Range | 18–90 °C |
| Humidity Range | 20–95 % RH |
| Compliance | IEC 60068-2-67, IEC 60068-2-78, ICH Q1A, USP <115>, ISO 17025 (when validated) |
| Key Features | Six-Side Heating, Heated Double-Glass Inner Door, Aluminum Thermal Mass Layer, Dynamic Humidity Control, AtmoCONTROL Software |
| Brand | MEMMERT |
|---|---|
| Origin | Germany |
| Model | HCP108 / HCP153 / HCP246 |
| Temperature Range (with humidity control) | +20 °C to +90 °C |
| Temperature Range (dry operation) | +20 °C to +160 °C |
| Humidity Range | 20–95 % RH |
| Temperature Uniformity (per DIN 12880 | 2007-05): ≤ ±0.3 °C at +50 °C |
| Temperature Stability (per DIN 12880 | 2007-05): ≤ ±0.1 °C at +50 °C |
| Sterilization Capability | +160 °C for 4 h |
| Internal Volume | 108 / 153 / 246 L |
| Power Consumption | ~1000 / 1500 / 2000 W |
| Compliance | DIN 12880, IEC 61000-6-3, IEC 61000-6-2, GLP-ready |
| Brand | MEMMERT |
|---|---|
| Origin | Germany |
| Model | HCP108 |
| Instrument Type | Upright Environmental Test Chamber |
| Internal Volume | ~108 L |
| Interior Dimensions (W×H×D) | 560 × 480 × 400 mm |
| Exterior Dimensions (W×H×D) | 710 × 778 × 550 mm |
| Interior Material | Electropolished Stainless Steel (Deep-Drawn) |
| Exterior Material | Stainless Steel Body with Galvanized Steel Rear Panel |
| Temperature Range (without humidity control) | 20–160 °C |
| Temperature Range (with humidity control) | 20–90 °C |
| Temperature Uniformity (per DIN 12880 at 50 °C) | ≤ ±0.3 °C |
| Temperature Stability (per DIN 12880 at 50 °C) | ≤ ±0.15 °C |
| Humidity Range | 20–95 % RH (capacitive sensor, sterilizable) |
| Humidity Control | Microprocessor-driven steam generation + desiccant-based dehumidification |
| Power Supply | 230 V / 50–60 Hz |
| Max. Power Consumption | ~1000 W |
| Net Weight | ~70 kg |
| Gross Weight | ~78 kg |
| Standard Accessories | 2 stainless steel sliding shelves (556 × 361 mm), factory calibration certificate (60 °C center point), Celsius 2005 software (standard), internal memory card (1024 KB ring buffer, ~3 months @ 1-min interval) |
| Brand | MEMMERT |
|---|---|
| Origin | Germany |
| Model | HCP153 |
| Instrument Type | Upright Environmental Test Chamber |
| Internal Volume | ~153 L |
| Chamber Dimensions (W×H×D) | 480 × 640 × 500 mm |
| External Dimensions (W×H×D) | 630 × 938 × 650 mm |
| Interior Material | Electropolished Stainless Steel (Deep-Drawn) |
| Exterior Material | Stainless Steel Front, Galvanized Steel Rear |
| Temperature Range (without humidity control) | 20–160 °C |
| Temperature Uniformity (per DIN 12880 at 50 °C) | ≤ ±0.3 K |
| Temperature Stability (per DIN 12880 at 50 °C) | ≤ ±0.15 K |
| Humidity Range | 20–95 % RH (capable of steam-based humidification and condensation-controlled dehumidification) |
| Humidity Sensor | Sterilizable Capacitive RH Sensor |
| Control System | Microprocessor-Based Fuzzy Logic Controller with Dual Pt100 A-Class (4-wire) Temperature Sensors |
| Data Logging | Built-in 1024 KB Circular Memory (≈3 months @ 1-min interval) |
| Communication Interfaces | Standard RS232, Optional RS485 / Ethernet / USB |
| Software | Celsius 2005 (standard), Celsius FDA Edition (21 CFR Part 11 compliant, optional) |
| Safety Systems | Triple Independent Temperature Protection (Mechanical TB, Electronic TWW, ASF Auto-Safety Function), Audible/Visual Alarms for Over-/Under-Temperature, Over-/Under-Humidity, Door Open, Empty Water Reservoir |
| Programmability | Up to 40-step time-temperature-humidity profiles via controller or MemoryCard XL |
| Certification | Factory Calibration Certificate (60 °C center point), Optional IQ/OQ Documentation Packages (DIN 12880, DIN 12900-1), STERICard for 160 °C Sterilization Cycle (4 h) |
| Brand | MEMMERT |
|---|---|
| Origin | Germany |
| Model | HCP246 |
| Chamber Type | Upright |
| Internal Volume | 246 L |
| Internal Dimensions (W×H×D) | 640 × 640 × 600 mm |
| External Dimensions (W×H×D) | 790 × 938 × 750 mm |
| Construction | Electropolished Stainless Steel Interior, Galvanized Steel Exterior |
| Temperature Range (without humidity control) | 20–160 °C |
| Temperature Uniformity (per DIN 12880, at 50 °C) | ≤ ±0.3 °C |
| Temperature Stability (per DIN 12880, at 50 °C) | ≤ ±0.15 °C |
| Humidity Range | 20–95 % RH (capable of sterilization at 160 °C) |
| Humidity Sensor | Sterilizable capacitive sensor |
| Control System | Microprocessor-based dual-loop PID controller with integrated diagnostics |
| Calibration | 3-point temperature & 2-point humidity calibration via front panel |
| Data Logging | 1024 KB circular memory (≈3 months @ 1-min interval) |
| Compliance | DIN 12880, DIN 12900-1, FDA 21 CFR Part 11 (with optional Celsius FDA Edition software), GLP/GMP-ready architecture |