- All
- Favorite
- Popular
- Most rated
| Brand | Memmert |
|---|---|
| Origin | Germany |
| Model Series | UNpa 30 / UNpa 55 / UNpa 75 / UNpa 110 / UNpa 160 |
| Temperature Range | +20 °C to +80 °C |
| Chamber Volume | 30 L / 55 L / 75 L / 110 L / 160 L |
| Heating Principle | Quadruple-wall conduction heating with passive thermal homogenization |
| Safety | Dual independent overtemperature protection (mechanical + electronic), hermetically sealed chamber design |
| Compliance | IEC 61010-1, EN 61326-1 (EMC), CE-marked for laboratory use |
| Brand | LAUDA |
|---|---|
| Origin | Germany |
| Model | Ultracool |
| Type | Refrigerated/Heating Recirculating Chiller |
| Circulation Mode | Internal & External |
| Temperature Range | 0–100 °C |
| Temperature Stability | ±0.1 °C (typical, dependent on load and ambient conditions) |
| Refrigerant | Low-GWP hydrofluoroolefin (HFO-1234ze, GWP < 250) |
| Enclosure Rating | IP54 |
| Max Ambient Operating Temperature | 50 °C |
| Construction | Electroplated copper housing with epoxy resin coating |
| Reservoir Material | Insulated polyethylene tank with integrated level switch |
| Heat Exchanger | External plate-type evaporator |
| Pump | High-efficiency stainless steel centrifugal pump with internal bypass |
| Safety Features | Freeze-protection thermostat, pressure monitoring switch, integrated water filter with biostatic additive |
| Optional Configurations | Stainless steel enclosure, casters, external bypass valve, deionized water compatibility, air-cooled or water-cooled condenser variants |
| Brand | Memmert (Germany) |
|---|---|
| Origin | Germany |
| Model | WTB |
| Construction | 304 Stainless Steel Interior |
| Control Interface | Capacitive Touchscreen with CustomView™ Personalization |
| Temperature Calibration | Dual-Point Adjustable Calibration |
| Standard Accessories | Stainless Steel Lid with Ventilation Peak |
| Optional Modules | Benchtop Platform, Tube Racks, Horizontal Shaking Module |
| Drainage | Rapid Full-Volume Drain Valve |
| Brand | LAUDA |
|---|---|
| Origin | Germany |
| Type | Refrigerated/Heating Circulating Bath |
| Temperature Range | −90 °C to +200 °C |
| Temperature Stability | ±0.01 °C (at 20 °C, depending on model and load) |
| Bath Volume | 5.5–35 L |
| Pump Flow Rate | Up to 25 L/min (pressure), 23 L/min (suction) |
| Pump Pressure Head | Up to 1.1 bar |
| Heating Power | 3.5 kW |
| Refrigeration Power | 0.38–1.6 kW (model-dependent) |
| Control Interface | Command or Master Controller |
| Circulation | Internal & External |
| Safety Features | Dual-level liquid level detection, overtemperature/overpressure/low-fluid alarms, dry-run protection, integrated error logging |
| Brand | INNOTEG |
|---|---|
| Origin | Guangdong, China |
| Model | TCS-3 |
| Instrument Type | Constant-Temperature Bath Chiller |
| Circulation Mode | External Circulation |
| Temperature Control | Refrigeration & Heating |
| Bath Volume | 5 L |
| Temperature Range | −20 °C to Ambient |
| Temperature Stability | ±0.3 K |
| Pump Type | Pressure/Suction Dual-Mode |
| Refrigeration Power | 0.45 kW @ 10 °C |
| Dimensions (W×D×H) | 222 × 480 × 495 mm |
| Weight | 25 kg |
| Temperature Sensor | PT100 |
| Display | High-Brightness LED |
| Safety Features | Over-Temp, Low-Level, Dry-Run, and Over-Pressure Protection |
| Brand | LAUDA |
|---|---|
| Origin | Germany |
| Model | Ecoline Star Edition |
| Temperature Control Type | Refrigerated/Heating Circulating Bath |
| Circulation Mode | Internal & External |
| Application | Primary Reference Standard for Thermometer and Sensor Calibration |
| Temperature Stability | ±0.01 °C (typical, dependent on model and operating conditions) |
| Temperature Range | –40 °C to +300 °C (model-dependent) |
| Bath Volume | 12–54 L |
| Pump Flow Rate | 12–25 L/min |
| Maximum Pump Pressure | 0.2–0.8 bar |
| Heating Power | 1.2–3.5 kW |
| Compliance | Designed for DKD/DAkkS-accredited calibration laboratories |
| Software Interface | RS232/RS485, optional Ethernet (via LAUDA TC software suite) |
| Brand | Memmert |
|---|---|
| Origin | Germany |
| Model | ICH Series |
| Temperature Uniformity | ≤ ±0.1 °C (at 25 °C, empty) |
| Humidity Range | 10–80 % RH (±1 % RH accuracy) |
| Air Circulation | Forced convection, adjustable in 10 % increments |
| Refrigerant | R744 (CO₂, GWP = 1) |
| Light Module | ICH Q1B Option 2 compliant — D65 daylight source (6500 K, ~8000 lux) + UV-A (320–400 nm) |
| CO₂ Control Module (optional) | IR-based, auto-zeroing, pressure-compensated, frost-free operation |
| IQ/OQ/PQ Support | Predefined calibration points — 3 temp setpoints, 2 humidity setpoints (20 % & 80 % RH), 3 CO₂ levels (5 %, 10 %, 15 %) |
| Brand | LAUDA |
|---|---|
| Origin | Germany |
| Model | ECO Silver / ECO Gold |
| Temperature Range | 20–200 °C |
| Display | Monochrome Graphical LCD (ECO Silver) or Color TFT LCD (ECO Gold) |
| Safety Class | Class III |
| Control Principle | Digital PID |
| Pump Type | Vario adjustable 6-stage circulation pump |
| Interface | Standard USB |
| Optional modules | Analog, Relay, RS232/485, PROFIBUS, Ethernet-USB, Pt100/LiBus |
| Mounting | Threaded clamp for baths with wall thickness ≤25 mm and depth ≥150 mm |
| Compliance | Suitable for flammable and non-flammable liquids |
| Certifications | CE, RoHS, IEC 61010-1 |
| Brand | Thermconcept |
|---|---|
| Origin | Germany |
| Model | High-Temperature Muffle Furnace |
| Max Operating Temperature | 1600 °C / 1750 °C / 1800 °C (configurable) |
| Chamber Volume | 16 L – 70 L |
| Heating Element | Dual-side MoSi₂ (optional rear-wall configuration) |
| Chamber Lining | High-purity alumina fiber insulation |
| External Casing | Polished stainless steel (AISI 304) |
| Door Mechanism | Parallel-guided safety door |
| Cooling | Optional forced-air cooling system |
| Exhaust | Top-mounted vent port with optional automatic exhaust lid |
| Atmosphere Options | Inert gas inlet (N₂, Ar), manual or programmable gas mixing module |
| Control System | Silent solid-state relay regulation with ±1 °C temperature stability (at setpoint) |
| Compliance | Designed per EN 61000-6-3 (EMC), EN 61000-6-2, and IEC 61010-1 for laboratory equipment safety |
| Brand | LAUDA |
|---|---|
| Origin | Germany |
| Model | PRO P10 |
| Bath Volume | 10–28.5 L |
| Temperature Range | 30 °C to 250 °C |
| Temperature Stability | ±0.01 K |
| Circulation Type | Internal & External |
| Standard Interfaces | USB, Ethernet |
| Brand | Thermconcept |
|---|---|
| Origin | Germany |
| Model | MoSi2 |
| Max Operating Temperature | 1700 °C / 1800 °C (short-term) |
| Tube Diameter Range | 38–75 mm |
| Heating Zone Length | 200–400 mm |
| Standard Tube Material | C799 ceramic |
| Insulation | Vacuum-formed high-purity alumina-silica fiber |
| Heating Element | Parallel-mounted MoSi₂ rods |
| Control | Solid-state semiconductor controller |
| Enclosure | Dual-wall housing with rear ventilation |
| Safety | EN 60519-2 compliant overtemperature limiter |
| Optional Configurations | Three-zone temperature control, vertical orientation with base stand, water-cooled flanges, gas-tight stainless steel flanges, manual/automated gas supply systems, internal water-cooling for rapid cooldown |
| Brand | LAUDA |
|---|---|
| Origin | Germany |
| Model | Aqualine |
| Instrument Type | Circulating Constant-Temperature Bath |
| Circulation Mode | Internal & External |
| Temperature Control | Heating & Cooling |
| Bath Volume Range | 1.7 L to 25.2 L |
| Temperature Range | 25 °C to 95 °C |
| Temperature Stability | ±0.2 K |
| Construction | Seamless Deep-Drawn Stainless Steel |
| Heating Element | Bottom-Mounted Surface Heater |
| Safety Features | Dry-run Protection (Min. Liquid Level: 20 mm), Over-Temperature Alarm |
| Display | LED Digital Interface |
| Lid Design | Hinged Stainless Steel Roof Lid with Condensate-Prevention Geometry |
| Compliance | Designed for GLP-compliant laboratory environments |
| Brand | Memmert (Germany) |
|---|---|
| Origin | Germany |
| Model Series | UN30, UN55, UN75, UN110, UN160, UN260, UN450, UN750, UN1060 / UF30, UF55, UF75, UF110, UF160, UF260, UF450, UF750, UF1060 |
| Temperature Range | +20 °C to +300 °C |
| Convection Options | Natural Convection (UN series) or Forced Convection with Adjustable Airflow (UF & UFplus series) |
| Air Exchange Control | Motorized damper with programmable opening angle (UFplus only) |
| Fresh Air Preheating | Integrated preheating chamber for incoming ambient air |
| Safety Certification | Complies with EN 61010-1, IEC 61000-6-3, and applicable parts of ISO 13485 when configured with A6 High-Temperature Alarm Module |
| Regulatory Use | Validated for sterilization of microbiological textiles and wrapping materials (per DIN EN ISO 17665-1 and DIN EN 285 when equipped with A6 module and operated within validated parameters) |
| Brand | Thermconcept |
|---|---|
| Origin | Germany |
| Model | KLS 07/11/M (1150 °C) / KLS 05/13/M (1300 °C) |
| Max Operating Temperature | 1150 °C or 1300 °C |
| Chamber Construction | High-purity ceramic muffle liner |
| Heating Configuration | Four-sided embedded heating elements |
| Insulation | Dual-wall steel housing with rear ventilation and low-surface-temperature design |
| Door Type | Top-lifting (KLS 07/11/M) or side-hinged (KLS 05/13/M) with ceramic fiber insulation |
| Control System | Silent solid-state relay temperature controller |
| Safety | EN 60519-2 compliant overtemperature limiter |
| Accessories | Stackable crucibles, ceramic/stainless steel collection trays (1300 °C / 1100 °C max), heat-resistant tongs (300 mm / 500 mm), gloves (600 °C / 900 °C) |
| Brand | LAUDA |
|---|---|
| Origin | Germany |
| Model | Integral P |
| Temperature Range | -40 to +140 °C |
| Heat Transfer Fluid | Non-flammable water/ethylene glycol mixture |
| Max Operating Pressure | 4 bar (gauge) |
| Pump Type | Magnetically coupled, electronically controlled |
| Flow Rate | Adjustable per application |
| Compatible Controller | LAUDA MID 80 Flow Control Unit |
| Application Focus | Automotive, Aerospace, EV Battery Thermal Testing |
| Brand | LAUDA |
|---|---|
| Origin | Germany |
| Model | Variocool |
| Cooling Capacity | Up to 10 kW |
| Temperature Range | –20 °C to +40 °C (–20 °C to +80 °C with optional heating module) |
| Temperature Stability | ±0.2 K |
| Max. Pump Pressure | 3.2 bar |
| Max. Flow Rate | 37 L/min |
| Power Supply Options | 208–230 V, 50/60 Hz |
| Optional Modules | Boost Pump, Water-Cooled Condenser, Flow Control, Low-Noise Kit, Outdoor Installation Kit |
| Brand | Thermconcept |
|---|---|
| Origin | Germany |
| Model | High-Temperature Muffle Furnace |
| Max Operating Temperature | 1500 °C, 1600 °C, 1750 °C, or 1800 °C |
| Chamber Uniformity | ±3 °C (at setpoint) |
| Construction | Dual-wall insulated cabinet with rear ventilation |
| Insulation | High-purity alumina fiber (low thermal conductivity, <0.12 W/m·K at 1000 °C) |
| Heating Elements | Dual-side mounted molybdenum disilicide (MoSi₂) rods |
| Control System | Solid-state relay (SSR) with PID algorithm |
| Temperature Accuracy | ±1 °C (typical, within operating range) |
| Safety Compliance | EN 60519-2 certified overtemperature protection |
| Optional Features | Motorized bottom door, inert gas inlet port, active cooling module, programmable exhaust damper |
| Brand | Thermconcept |
|---|---|
| Origin | Germany |
| Model | High-Temperature Muffle Furnace |
| Max Operating Temperature | 1400 °C / 1500 °C / 1600 °C |
| Heating Element | Silicon Carbide (SiC) rods, laterally mounted |
| Chamber Lining | Ceramic fiber insulation |
| Enclosure | Dual-wall construction with rear ventilation |
| Door Type | Top-hinged lift door with reinforced fiber seal |
| Base Lining | High-temperature ceramic fiber board |
| Standard Accessories | Ceramic hearth plate |
| Temperature Control | Solid-state relay with PID algorithm |
| Exhaust Port | Integrated vent opening on top |
| Surface Temperature | <60 °C at ambient conditions |
| Compliance | Designed to meet EN 61000-6-3 (EMC), EN 61000-6-2, and general lab safety requirements per DIN VDE 0701-1 |
| Brand | LAUDA |
|---|---|
| Origin | Germany |
| Model | Proline PJ12 / PJ12 C / PJL12 / PJL12 C |
| Temperature Range | –40 °C to +300 °C |
| Heating/Cooling Medium | Liquid (e.g., silicone oil, water-glycol) |
| Control System | Microprocessor-based PID with PowerAdapt and SelfCheck diagnostics |
| Pump Type | LAUDA Varioflex pressure pump (8 adjustable levels) |
| Display | Green LED, EasyUse 3-button interface |
| Communication Interfaces | RS-232/485, Profibus, analog/contact modules, Ethernet/USB (optional) |
| Safety Features | Dual-stage overtemperature protection, audible alarm, flammable/non-flammable liquid mode |
| Brand | Memmert (Germany) |
|---|---|
| Origin | Germany |
| Model | IN / IF Series |
| Temperature Range | Ambient +5°C to +80°C |
| Convection Type | Natural Convection (IN) / Adjustable-Speed Forced Convection (IF) |
| Sterilization Capability | 160°C for 4 h (INplus/IFplus models) |
| Fresh Air Preheating System | Integrated preheating chamber |
| Compliance | Designed for GLP/GMP environments, supports FDA 21 CFR Part 11–compliant software validation (with optional VarioControl software) |
| Brand | Thermconcept |
|---|---|
| Origin | Germany |
| Model | TC-UF Series (1100 °C / 1200 °C variants) |
| Temperature Range | Up to 1100 °C or 1200 °C |
| Construction | Stainless steel exterior, high-purity ceramic fiber insulation |
| Heating Element | Embedded resistance wire in ceramic heating plates |
| Control System | Silent solid-state relay with PID temperature regulation |
| Safety | Dual-stage overtemperature protection per EN 60519-2 |
| Exhaust Options | Optional exhaust chimney with fan and catalytic converter |
| Compliance | Designed for GLP-compliant laboratory environments |
| Brand | Thermconcept |
|---|---|
| Origin | Germany |
| Model | Compact Tube Furnace |
| Max Operating Temperature | 1100 °C (single-zone) / 1300 °C (triple-zone) |
| Tube Diameter | 200 mm |
| Heating Zone Length | 500 mm (extendable) |
| Heating Element Control | Solid-state relays (1100 °C) or semiconductor controllers (1300 °C) |
| Temperature Uniformity | Optimized via vacuum-formed ceramic fiber insulation |
| Safety Compliance | Overtemperature protection per EN 60519-2 |
| Controller Location | Bottom-mounted for ergonomic access |
| Optional Configurations | Vertical orientation, custom tube materials (quartz, alumina, stainless steel), extended heating zones |
| Brand | INNOTEG |
|---|---|
| Model | TCS-2 |
| Type | Refrigerated/Heating Circulating Bath |
| Capacity | 10 L |
| Temperature Range | −20 °C to 100 °C |
| Temperature Stability | ±0.05 °C (at 25 °C, water or ethanol) |
| Display Resolution | 0.1 °C |
| Cooling Power | 0.47 kW @ 20 °C |
| Bath Opening Dimensions | 215 mm × 170 mm × 150 mm (W × D × H) |
| Circulation Mode | Internal & External |
| Control System | Microprocessor-based PID with Auto-tuning |
| Construction | 304 Stainless Steel Interior, Insulated Foam Housing |
| Safety Features | Dual-level Liquid Level Detection (Visual + Audible Alarm), Dry-run Protection, Independent Heating/Cooling Status Indicators, Programmable Heating Timer |
| Brand | Memmert (Germany) |
|---|---|
| Origin | Germany |
| Model Variants | ICO 50 / ICO 105 / ICO 150 / ICO 240 |
| Temperature Range | +18 °C to +50 °C |
| Humidity Range | 40–97 % RH (optional) |
| CO₂ Concentration Range | 0–20 % |
| O₂ Concentration Range | 1–20 % (optional) |
| Sterilization | Dry-heat at 180 °C for 60 min |
| Data Storage | Internal SD card (10-year capacity) |
| Compliance | FDA 21 CFR Part 11–ready, GLP/GMP-supportive architecture |
Show next