- All
- Favorite
- Popular
- Most rated
| Brand | UIC (United Instruments Corporation) |
|---|---|
| Origin | USA |
| Model | 833 |
| Molecular Weight Range | 100–25,000 Da (in toluene), 100–5,000 Da (in water) |
| Minimum Detectable Concentration | 5 × 10⁻⁵ mol/L (toluene), 2.5 × 10⁻⁴ mol/L (water) |
| Temperature Control Range | Ambient to 130 °C (with optional cryo-circulator for sub-ambient operation) |
| Cell Current Settings | 5, 20, 100 µA |
| Equilibration Time | 2–5 min per sample |
| Sample Volume | 0.25 mL |
| Construction | All-metal hermetic cell housing with dual needle-port inlet system |
| Origin | USA |
|---|---|
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | 2701 |
| Pricing | Available Upon Request |
| Max Operating Temperature | 1913 °C |
| Arc Current Range | 400–600 A |
| Argon Gas Flow Requirement | 50 L/min |
| Crucible Material | Water-Cooled Copper |
| Anode Options | Graphite, Carbon, Tungsten |
| Typical Melting Time | ≤60 s |
| Sample Forms Accepted | Powders, Drill Chips, Cut Strips, Slurries |
| Max Sample Mass (Steel) | 50 g (Ø31.8 mm × 6.4 mm) |
| Brand | MIKROLAB |
|---|---|
| Origin | Denmark |
| Model | OXIPRES |
| Sample Capacity | 100 mL (with ≥5 g fat) |
| Operating Pressure | up to 10 bar (1 MPa) |
| Temperature Range | 30–150 °C |
| Heating Block Max Temp | 150 °C |
| Pressure Sensing | Electronic transducer |
| Output Signal | 1 V FS or 5 V FS |
| Dimensions (2/4/6-sample configurations) | 41 × 30 / 62 × 30 / 83 × 30 cm |
| Footprint | ~600 mm (excl. PC) |
| Power Supply | 230 V / 50 Hz, max. 8 A |
| Software | PARALOG v3 |
| Gas Charging Station | Dual- or hexa-port with safety valve |
| Sample Vessel | 125 mL borosilicate glass jar with sealing lid and O-ring |
| Origin | Poland |
|---|---|
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported Instrument |
| Model | SPD2.2 |
| Price Range | USD 27,000 – 68,000 |
| Compliance | ASTM E1226, ASTM E1515, EN 14034-1:2004+A1:2011, EN 14034-2:2006+A1:2011, EN 14034-3:2006+A1:2011 |
| Vessel Volume | 20 L |
| Vessel Material | AISI 316 Stainless Steel |
| Maximum Working Pressure | 40 bar (gauge) |
| Pressure Measurement Range | 0–25 bar (absolute) |
| (dp/dt)max Detection Threshold | >4000 bar/s |
| Kst Range | >1000 bar·m/s |
| Explosibility Parameters | LEL/UEL/MEC from 0 g/m³, LOC: 1–21 % O₂ |
| Dust Injection Valve Response Time | ≤30 ms |
| Vacuum Display Range | 0–1 bar (absolute) |
| Vacuum Control | Auto & Manual Modes |
| Vessel Temperature Monitoring | Front-panel digital readout |
| Data Acquisition Rate | 10–100 kHz |
| Software | ANKO Explosion Plotter v3.x (GLP-compliant reporting, audit trail, test sequence automation, noise-filtered signal processing, PDF report generation) |
| Accessories | Integrated vacuum pump unit, exhaust scrubber with flow controller, borosilicate observation viewport, dedicated workstation, thermal printer |
| Origin | Italy |
|---|---|
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported Instrument |
| Model | HTM1400 |
| Pricing | Upon Request |
| Brand | BUCK |
|---|---|
| Origin | USA |
| Instrument Type | Benchtop Laboratory Analyzer |
| Principle | Cold Vapor Atomic Absorption Spectrometry (CVAAS) |
| Detection Wavelength | 253.7 nm |
| Detection Limit | 10 pg/L (ppt) under controlled clean-lab conditions |
| Sample Cell Path Length | 400 mm fused silica window |
| Background Correction | Online Deuterium Lamp (D₂) |
| Output Interfaces | RS-232 serial port, analog output (0–1 V or 4–20 mA) |
| Sample Introduction | Air-driven purge-and-trap with integrated desiccant and charcoal filtration |
| Dimensions (W×D×H) | 991 × 279 × 305 mm |
| Weight | 21 kg |
| Power Requirement | 220 V, 50 Hz, 80 W |
| Compliance | Fully compliant with U.S. EPA Method 245.1 |
| Calibration | Up to 8-point linear or quadratic calibration curves |
| Operational Features | Quick-Purge button for flow-cell cleaning, Peak-Picker peak-area integration, GLP-ready data handling |
| Origin | UK |
|---|---|
| Type | Box-Type Muffle Furnace |
| Max Temperature | 1700°C or 1800°C |
| Chamber Volume | 4 L to 27 L |
| Heating Elements | MoSi₂ or Mo–W–Si₂ |
| Control Options | Eurotherm 2116 / 2216 / 2416 CG / 2408 CP |
| Power Range | 4.4 kW to 15.0 kW |
| Door Operation | Manual or Motorized |
| Safety Features | Over-Temperature Protection, Electronic Door Lock, Vertical Lift Door, Dual-Wall Insulated Housing |
| Brand | Reichert |
|---|---|
| Origin | USA |
| Model | Brix/RI-Chek |
| Product Type | Handheld Refractometer |
| Temperature Control | Yes (ATC) |
| Digital Display | Yes (5-digit full-view LCD) |
| Refractive Index Range | 1.3330 – 1.4465 |
| RI Accuracy | ±0.0002 |
| Brix Range | 0.0 – 62.0% |
| Brix Accuracy | ±0.2% |
| Prism Material | Optical Glass |
| Dimensions | 54 × 27 × 100 mm |
| Weight | 100 g |
| IP Rating | IP65 |
| Certifications | CE, RoHS, WEEE |
| Warranty | 1 year |
| Order Code | 13940000 |
| Origin | Switzerland |
|---|---|
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | ASTM D566 |
| Pricing | Upon Request |
| Origin | Imported |
|---|---|
| Manufacturer Type | Authorized Distributor |
| Detection Principle | Non-Dispersive Infrared (NDIR) |
| Model | CS2000M |
| Measurement Range | C: 0–100%, S: 0–100% |
| Accuracy | ±1% of measured content |
| Analysis Time | 90 s (typical) |
| Sample Mass | 300–500 mg |
| Combustion Temperature | Ambient to 1400 °C |
| Oxygen Purity | >99.5%, Pressure: 40 PSI |
| Gas Flow Rate | 3.0 L/min |
| Reagent | Magnesium Perchlorate |
| Interface | 4 RS-232 ports for analytical balance integration |
| Origin | Imported |
|---|---|
| Manufacturer Type | Authorized Distributor |
| Detection Principle | Non-Dispersive Infrared (NDIR) |
| Model | CSBox-Tube-S |
| Measurement Range | 0.005–100 wt% S |
| Accuracy | ±1% relative (typical samples) |
| Sample Mass | 10–200 mg |
| Analysis Time | 40–300 s |
| Combustion Temperature | 800–1500 °C (configurable by mode) |
| Interface Protocol Support | Sartorius, Mettler, Precia, Ohaus (RS-232/USB), manual entry |
| Data Output | LPT, COM, USB, LAN (RJ45) |
| Operating System | FreeDOS on Advantech industrial motherboard |
| Origin | New Zealand |
|---|---|
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | 5400RHS |
| Price | Upon Request |
| Temperature Range | −10 °C to +100 °C |
| Temperature Stability | ±0.3 °C |
| Temperature Uniformity | ±0.75 °C |
| Humidity Range | 35–98 %RH |
| Humidity Accuracy | ±2 %RH |
| Effective Volume | 400 L |
| Internal Dimensions (W×D×H) | 640 × 540 × 1225 mm |
| External Dimensions (W×D×H) | 890 × 870 × 2045 mm |
| Shelf Capacity | 6 adjustable stainless-steel shelves |
| Cooling Rate | 70 °C → 0 °C in ≤60 min |
| Heating Rate | −10 °C → 70 °C in ≤45 min |
| Power Consumption | 1750 W |
| Net Weight | 200 kg |
| Gross Weight | 240 kg |
| Compliance | NZS 6200, AS/NZS 3100, IEC 61010-1 |
| Origin | Czech Republic |
|---|---|
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported Instrument |
| Model | Deasphaltop |
| Pricing | Available Upon Request |
| Origin | Imported |
|---|---|
| Manufacturer Type | Authorized Distributor |
| Model | E2K |
| Operating Temperature Range | 0–60 °C |
| Temperature Repeatability | ≤0.1% RSD |
| Temperature Resolution | 1 µK |
| Gross Calorific Value Resolution | 0.001 MJ/kg |
| Calibration | 10 stored calibration curves per smart bomb vessel, automatic standard deviation correction, integrated calibration sensors per vessel |
| Sample Throughput | Up to 10 samples/hour (standard configuration) |
| Measurement Time | 1.5–3 min per test |
| Dimensions (W×D×H) | 280×400×290 mm |
| Weight | 9 kg |
| Data Storage Capacity | >1000 test records with full metadata (operator ID, ambient conditions, calibration traceability) |
| Connectivity | Ethernet-enabled for multi-unit network (up to 7 units) |
| Ignition Control | Adjustable ignition energy, programmable high/low sample mass limits, customizable test cycle parameters |
| Brand | UIC (USA) |
|---|---|
| Origin | USA |
| Model | CM350 |
| Category | Other Elemental Analyzers |
| Compliance | ASTM D3120, D3246, D5453 |
| Detection Principle | Coulometric titration based on Faraday’s law |
| Dynamic Range | 1 µg – 10,000 µg sulfur (equivalent to ~1 ppm – 100% w/w, sample-dependent) |
| Resolution | 0.01 µg S |
| Analysis Time | 5–7 min (combustion mode), ≤15 min (acid digestion mode) |
| Sample Forms | Solids (0.5 mg – 10 g) and liquids |
| Furnace Max Temp | 1100 °C |
| Data Storage | Internal floppy drive (CM5014S), exportable via RS232 |
| Origin | Switzerland |
|---|---|
| Type | ASTM D86 Compliant Manual Atmospheric Distillation System |
| Model | 1000 Series |
| Configuration | Modular (Heating Unit 990/A + Condensation Unit 990/B) |
| Compliance | ASTM D86, IP 62–88, ISO 3405 |
| Heating Control | Electronically Adjustable Stainless Steel Heating Plate |
| Condenser | Chrome-Plated Copper Tubing with Water-Circulated Jacket |
| Visibility | Front-Mounted Tempered Glass View Window |
| Bottle Capacity Options | 100 mL (Type A), 125 mL (Type B), 200 mL (Type C), 250 mL (Type D) |
| Receiver Volumes | 25 mL (Type A), 100 mL (Type B), 200 mL (Type C) |
| Temperature Measurement | ASTM/IP Calibrated Thermometers (ASTM 2C to 107C / IP 62C to 88C) |
| Origin | UK |
|---|---|
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | XTRA Oil-in-Water Analyzer |
| Pricing | Upon Request |
| Origin | Switzerland |
|---|---|
| Type | ASTM D92 Cleveland Open Cup Flash Point Tester |
| Temperature Range | +79 °C to +400 °C |
| Temperature Resolution | 0.06 °C |
| Temperature Accuracy | ±0.1 °C |
| Temperature Probe | PT100 Platinum Sensor (1/10 DIN Class) |
| Sample Cup | ASTM D92 / IP 36–compliant dimensions and fill level markings |
| Heating System | Electronic heater with overtemperature protection |
| Repeatability & Reproducibility | Meets or exceeds ASTM D92 and IP 36 requirements |
| Dimensions (W×D×H) | 48 × 37 × 61 cm |
| Weight | 32 kg |
| Power Supply | 220 V ±15 %, 50/60 Hz |
| Ambient Operating Limit | ≤35 °C |
| Safety Certification | CE-marked |
| (Origin | Italy |
|---|---|
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | D323 |
| Pricing | Available Upon Request) |
| Brand | Linetechnic |
|---|---|
| Origin | Switzerland |
| Model | 225 / D2068 |
| Compliance | ASTM D2068, IP 387 |
| Operating Temperature Range (Bath) | −10 °C to +40 °C |
| Sample Temperature Range | −50 °C to +80 °C |
| Flow Rate | 20 mL/min |
| Pressure Measurement Range | 0–210 kPa |
| Max. Pressure Threshold | 105 kPa |
| Filtration Capacity Resolution | 0.1 mL |
| Temperature Sensor | PT100 Class A |
| Bath Material | Anodized Aluminum |
| Cooling System | Single-phase air-cooled compressor, CFC-free refrigerant |
| Data Storage Capacity | 60,000 test records |
| Display | 6.4″ TFT/LCD touchscreen (640 × 480 pixels) |
| Processor | AMD Geode 800 |
| Interface | 1 × USB, 1 × 10/100 Mbps LAN |
| Safety Certification | CE |
| Brand | Linetechnic |
|---|---|
| Origin | Switzerland |
| Model | 1300 |
| Temperature Range | +80 °C to –80 °C |
| Cooling System | Single-stage or dual-stage compressor (–40 °C or –85 °C min) |
| Temperature Sensor | PT100 Class A |
| Temperature Resolution | 0.06 °C |
| Temperature Accuracy | ±0.1 °C |
| Compliance | ASTM D2500, D5771–D5773, D97, D5950, D5853 |
| Optical Detection | Pulsed IR fiber-optic probe for cloud point |
| Mechanical Detection | Dual PT100 surface probes + motorized tilt arm for pour point |
| Origin | Russia |
|---|---|
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported Instrument |
| Model | IM Series |
| Measurement Parameters | Gasoline Octane Number (ON), Diesel Cetane Number (CN) |
| Portability | Handheld Field-Deployable |
| Measurement Range | 40–120 ON, 40–60 CN |
| Accuracy | ±0.5 ON, ±1.0 CN |
| Analysis Time | <10 s per sample |
| Sample Volume | 10 mL |
| Temperature & Cloud Point Measurement | Integrated digital thermometry and diesel cloud point estimation |
| Compliance | ASTM D2699-86, ASTM D2700-86, ASTM D4737-03, ASTM D613, EN ISO 5165 |
| Calibration Interface | RS-232 serial connection for PC-based calibration using Windows Mobile-compatible software (Pocket PC 2000/2002) |
| Power Supply | 5.2 V DC internal / 5.8 V external |
| Dimensions (Main Unit) | 100 × 210 × 40 mm |
| Probe Dimensions | Ø60 × 100 mm |
| Battery Life | Up to 1000 hours of cumulative operational time |
| Origin | USA |
|---|---|
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | Badger |
| Instrument Type | Jaw Crusher |
| Sample Applicability | Brittle Materials (e.g., rocks, ores, ceramics, metals, chemicals) |
| Feed Size | < 15 mm |
| Discharge Size | ≥ 0.5 mm |
| Batch Capacity | 60 mL |
| Jaw Opening | 127 mm × 178 mm |
| Motor | 3 HP, 3-Phase, 380 V, 400 rpm |
| Bearing Type | Sealed Spherical Roller Bearings |
| Crushing Capacity | 590 kg/h |
| Jaw Plate Material | Chrome Steel (standard) |
| Base & Guard | Stainless Steel |
| Origin | UK |
|---|---|
| Manufacturer Type | Authorized Distributor |
| Origin Category | Imported |
| Model | BMF11/7 |
| Instrument Type | Box-Type Muffle Furnace |
| Max Temperature | 1100 °C |
| Operating Temperature Range | Ambient to 1050 °C (continuous) |
| Temperature Uniformity | ±5 °C at 1050 °C |
| Control Accuracy | ±2 °C |
| Internal Dimensions (W×D×H) | 178 × 305 × 125 mm |
| Effective Volume | 7 L |
| Max Power Consumption | 2 kW |
| Heating Rate to 1100 °C | ≤50 min |
| Heating Element | Dual-sided Kanthal A1 wire embedded in ceramic fibre grooves |
| Insulation | Low-mass, high-purity ceramic fibre (density ~128 kg/m³) |
| External Casing | Galvanised steel with polyester powder coating |
| Door Mechanism | Top-hinged or front-hinged insulated door with automatic power cut-off interlock |
| Exhaust | Integrated chimney port (standard) |
| Thermocouple | Type N (NiCr–NiSi), calibrated per IEC 60584 |
| Electrical Supply | 240 V AC, single-phase |
| Net Weight | 48 kg |
| Compliance | CE-marked, conforms to EN 61000-6-3 (EMC), EN 61000-6-2 (Immunity), EN 60519-1 (Electrical Safety for Industrial Heating Equipment) |
Show next